PX-22 SHEARTEC II PLANER
40
Shear-Tec II Knife Rotation/Replacement
CAUTION!
KNIFE INSERTS ARE DANGEROUSLY SHARP. USE EXTREME CAUTION WHEN INSPECTING,
REMOVING, OR REPLACING KNIFE INSERTS.
WARNING!
•
TURN PLANER OFF AND DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE OR
ADJUSTMENTS!
•
MAKE SURE ALL KNIFE INSERT SCREWS ARE TIGHTENED SECURELY. LOOSE INSERTS CAN BE
PROPELLED AT HIGH SPEED FROM A ROTATING CUTTERHEAD, CAUSING INJURY.
TORQUE EACH SCREW TO 52-60 IN/LBS or 231-267 Newtons.
•
KNIVES ARE EXTREMELY SHARP. BE VERY CAREFUL WHEN HANDLING KNIVES. FAILURE TO COMPLY
MAY CAUSE SERIOUS INJURY.
The knife inserts on the Planer are four-sided. When dull, remove each knife, rotate it 90° for a fresh edge, and re-
install it. No further adjustment is necessary.
Use a Torx wrench (T25)
to remove the knife insert screw. Use a
second Torx wrench to hold the cutterhead (from rotating) in position (in another screw). DO NOT USE YOUR
HAND TO HOLD THE CUTTERHEAD!
(See Figure Below).
It is advisable to rotate all inserts at the same time to maintain consistent cutting. However, if one or more knife
inserts develops a nick, rotate only those inserts that are affected. Each knife insert has an etched reference mark
Содержание SHEARTEC II PX-22
