laguna CFlux 3, Руководство по эксплуатации

Страница: 6 / 82

-6- www.igmtools.com
Hand held remote controller
Pic. 3
PROGRAMMING THE REMOTE CONTROL
1. Ensure the machine is ON before programming the remote control.
2. Press the BLACK set button on the bottom of the remote switch until
you hear two beeps.
3. Press the Remote set button on your hand held controller
simultaneously with the BLACK button until you hear three beeps to
complete the set up.
Pic. 4
5. Assembly
5.1 Unpacking
Your 3HP Mobile Dust Cyclone comes packed in a single box. Before
attempting to assemble this machine, follow these directions for
unpacking:
1. Carefully cut the banding straps and remove them from the box.
2. Cut along the tape line at the top of the box.
3. Remove all parts from the top of the styrofoam and set aside.
4. Remove the styrofoam packing material from the top of the machine.
5. Carefully take out the machine components from the box and set aside.
6. Using the diagram below, ensure that all parts are present and in good
condition.
Pic. 5
Description
A. Motor
B. Switch and remote controller
C. Dust chute
D. Top upright supports (3)
E. Canister 1 Micron
F. Base frame
G. Octagon front and back panel
H. Octagon drum side panels
I. Octagon drum lid
J. Cyclone funnel
K. Cyclone barrel
L. Intake cylinder
M. Canister cover plate
N. Octagon drum foot peddle
O. Inlet adapter
P. Lower upright supports (3)
Q. Drum insert
R. Upright support reinforcement plate (3)
S. Foot peddle bar (left and right)
T. Foot peddle assembly fittings
T1. Lower triangular support plate (2)
T2. Foot peddle bar support (2)
T3. Lower support plate (2)
U. Hardware box
V Operating and Parts Manual
Report any missing or damaged parts to your dealer or distributor. Prior to
tool assembly and use, read this manual thoroughly to familiarize yourself
with proper assembly, maintenance and safety procedures.
5.2 General Tool Assembly
This step requires two adults.
This 3HP Mobile Dust Cyclone is heavy,
be careful when lifting and handling it! Failure to comply may cause
serious injury and/or damage to the machine and/or property!
Tools Required
10 mm wrench / 12 mm wrench / 14 mm wrench
Phillips screwdriver. 4 mm hex wrench / 5 mm hex wrench
To assemble your dust cyclone, follow these steps:
For your own safety, do not connect the machine to the power source until
the machine is completely assembled. Please also make sure that you
read and understand the entire instruction manual.
ASSEMBLY TIME ESTIMATE 4-5 hours
Step 1: Turn the unit upside down. Make sure you use a cushion under
the canister top side to even out the unit to the same height as the motor.
Do not have the unit lopsided. Remove the base (G) which has been
fastened to the (3) top upright supports (E).
Pic. 6
Step 2: Secure the (4) 76 mm wheels to the underside of the base (F)
using (16) 8 mm*19 mm hex bolts and (16) 8 mm*OD18*2T flat washers.
Pic. 7
Step 3: Turn the base (F) around with it standing on the 4 red
wheels and secure the three lower upright support panels (P) using hex
bolts (6) 9 mm*19 mm and flat washers (6) 9 mm*OD23*2T.
Each lower upright support panels (P) numbered for its specific location.
A – shown with one dot is located on the canister side. B – shown with two
dots with extension on left is located on the front side. C – shown with two
dots with extension on right is located on opposite end.
B
T1
A J
Q P T2
T3
C
G
J
E
D
l
N
T
R
U
F
G
H
K K
M
O
L
S
T
V
Manuál
N ář adí
3HP Mobile Dust Cyclone Manual
10
IN ALL CASES, MAKE CERTAIN THE RECEPTACLE IN QUESTION IS
PROPERLY GROUNDED. IF YOU ARE NOT SURE, HAVE A QUALIFIED ELECTRICIAN CHECK
THE RECEPTACLE.
240 VOLT Single-Phase Operation
The motor supplied with your machine is a 240 volt motor. It is shipped ready-to-run
for 240volt operation.
FUNCTION
High frequency remote control switch
Hand held remote controller
OFF button ON button
*Remote set button
*Used to match up a new hand held
controller with the remote switch
ON/OFF Switch
Motor Cord
On board circuit breaker
Power Cord
Receiver set
button
Hardware
box
Manual
ON button
OFF button
Remote set button
*Used to match up a new hand held
controller with the remote switch