Labom PASCAL CS21 0 Series Скачать руководство пользователя | Manualshive

Страница: 2 / 20

background image

BA_060 Rev 1B6 Pressure transmitter PASCAL CS

Page 2/20

1

General Information

This document contains necessary information for the proper installation and use of this
device. In addition to this instruction, be sure to observe all statutory requirements, appli-
cable standards, the additional technical specifications on the accompanying data sheet
(see www.labom.com) as well as the specifications indicated on the type plate.

1.1 General Safety Notes

The installation, set up, service or disassembly of this device must only be done by
trained, qualified personnel using suitable equipment and authorized to do so.

Warning

Media can escape if unsuitable devices are used or if the installation is not
correct.

Danger of severe injury or damage

Ensure that the device is suitable for the process and undamaged.

1.2 Intended Use

The device is intended to measure pressure of gases, vapors and liquids as specified in
the data sheet.

1.3 Conformity with EU Regulations

The CE-marking on the device certifies its compliance with the applicable EU Directives for
placing products on the market within the European Union.

The following guidelines apply to these devices:

PED Directive

2014/68/EU

EMC Directive

2014/30/EU

You find the complete EC Declaration of Conformity (document no. KE_035) at
www.labom.com.

2

Transportation and Storage

Store and transport the device only under clean and dry conditions preferably in the origi-
nal packaging. Avoid exposure to shocks and excessive vibrations.

Permissible storage temperature:

-40…85 °C

3

Installation and Commissioning

Ensure that the device is suitable for the intended application with respect to pressure
range, overpressure limit, media compatibility, temperature range and process connection.

3.1 Mechanical Installation

Use gaskets, if required, that are suitable for the process connection and resistant to the
media.

Before starting operation, check the process connection carefully for leaks under pressure.

You can use the device in any mounting position. Normally the transmitter is adjusted for a
vertical mounting position. A different mounting position in combination with a small nomi-

«
1
2
3
4
...
»

Содержание PASCAL CS21 0 Series





















Отзывы:

Нет отзывов

Похожие инструкции для PASCAL CS21 0 Series

Бренд: Omega Страницы: 32

Бренд: Yaesu Страницы: 77

100 WATT / 70 VOLT MONO VOLUME CONTROL

Бренд: Audioplex Страницы: 2

Бренд: Icom Страницы: 64

Бренд: halstrup-walcher Страницы: 12

Бренд: BBC Bircher Страницы: 4

Бренд: DTC Страницы: 123

Бренд: Inova Страницы: 37

Бренд: JVC Страницы: 2

Kenwood TK-5220

Бренд: JVC Страницы: 128

Бренд: Zonda Страницы: 2

Бренд: CE Labs Страницы: 2

Бренд: IFM Страницы: 5

Бренд: HYDAC ELECTRONIC Страницы: 24

Бренд: HYDAC ELECTRONIC Страницы: 31

Бренд: Garmin Страницы: 7

Бренд: Garmin Страницы: 44

Бренд: Garmin Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды