Labom PASCAL CS21 0 Series Скачать руководство пользователя страница 18

Страница: 18 / 20

BA_060 Rev 1B6 Pressure transmitter PASCAL CS

Page 18/20

6.6 System Menue (

SYS

)

The system menue contains the following items:

Display

Designation Description

Information

Display of Hardware and software version, serial number

Reset

Return

Return to "

SYS

Table 14: The items in the system menue

6.6.1

Information (

inFo

)

The following device information is available in the system menue.

Display

Designation

Display

Designation

Hardware version 1 (HW1)

Serial number 1 (Sn 1)

Hardware version 2 (HW2)

Serial number 2 (Sn 2)

Software version 1 (SW1)

Serial number 3 (Sn 3)

Software version 2 (SW2)

Serial number 4 (Sn 4)

Return

Return to "

inFo

Table 15: Menue items in the information menue

Due to the limited number of alphanumerical segments on the display, hardware and soft-
ware versions are split into two separate items, and serial number into four items.

6.6.2

Reset to factory settings (

rES

)

You can reset the device to the configuration as delivered with the menue item "Reset"
(

rES

). When the menue item is selected the entry points to "

-rEt-

". To trigger the func-

tion go to "

YES

" with one of the arrow buttons and confirm with the middle button. This ex-

tra step prevents any unintentional reset while navigating the menue.

donE

" appears on the display to confirm that the device has been reset to factory settings

and the device switches back to the menue item "Reset" (

rES

). The factory reset does not

affect the zero point adjustment.

Display

Designation

Description

Return

Return to "

rES

Confirm (yes)

Resetting the device to factory settings

Table 16: Parameter list for resetting the device to factory settings

Содержание PASCAL CS21 0 Series





















Результаты поиска

Содержание PASCAL CS21 0 Series

Отзывы:

Бренды по названию

Популярные бренды

Labom PASCAL CS21 0 Series, Руководство по эксплуатации

Результаты поиска

Содержание PASCAL CS21 0 Series

Отзывы:

Бренды по названию

Популярные бренды