Labnet C0226R страница 12 Скачать руководство пользователя

Страница: 12 / 66

Maintenance conditions

START-UP

Prior to switching the centrifuge on, one shall read carefully all sections of

this instruction in order to ensure smooth operation and avoid damages of

this device or its accessories.

In order to protect the centrifuge against unbalance, fill in the test tubes up

to the same weight.

TRANSPORTATION

Centrifuge must not be transported with the rotor mounted on the shaft.

GENERAL HINTS

One must use original rotors, test-tubes and spare parts only.

In case of faulty operation of the centrifuge one shall ask for assistance

service of LABNET INTERNATIONAL/Corning or its authorized

representatives.

NEVER switch the centrifuge on if it is not installed properly or rotor is not

fitted correctly.

CENTRIFUGING SUBSTANCES

NEVER exceed load limit set by the manufacturer. Rotors are intended for fluids

of average homogeneous density equal to 1,2 g/cm

or smaller when

centrifugation is carried out at maximum speed. When fluids of higher density

shall be used, then it is necessary to change density of centrifuges sample in

PARA/DENSITY field.

Содержание C0226R



































































Результаты поиска

Содержание C0226R

Отзывы:

Похожие инструкции для C0226R

Бренды по названию

Популярные бренды

Labnet C0226R, Руководство пользователя

Результаты поиска

Содержание C0226R

Отзывы:

Похожие инструкции для C0226R

Бренды по названию

Популярные бренды