manualshive.com logo in svg
background image

FCC information

FOR CLASS B UNINTENTIONAL RADIATORS

This equipment has been tested and found to comply with the limits for a Class B 

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-

vide reasonable protection against harmful interference in a residential installation. 

This equipment generates, uses and can radiate radio frequency energy and, if not 

installed and used in accordance with the instructions, may cause harmful interference 

to radio communications. However, there is no guarantee that interference will not 

occur in a particular installation. If this equipment does cause harmful interference 

to radio or television reception, which can be determined by turning the equipment 

off and on, the user is encouraged to try to correct the interference by one or more of 

the following measures:

• 

Reorient or relocate the receiving antenna.

• 

Increase the separation between the equipment and receiver.

• 

Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected.

• 

Consult the dealer or an experienced radio/TV technician for help.

FCC INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-

lowing two conditions: (1) this device may not cause harmful interference, and (2) this 

device must accept any interference received, including interference that may cause 

undesired operation.

W

 

WARNING

: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR 

RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES 

AND FEDERAL LAW. 

A

 

CAUTION:

 Changes  or modifications to this device, not expressly approved 

by Lab599 Inc., could void your authority to operate this device under   

FCC regulations.

Amateur Radio Operation Only

14

Содержание Discovery TX-500

















Отзывы: