Lab.gruppen FP+ Series FP 10000Q Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 31

Lab.gruppen FP+ Series FP 10000Q Скачать руководство пользователя страница 18

18

FP+ Series Operation Manual

Two-channel amplifiers

– Two-channel amplifiers

are wired in the following manner. The right Speakon
connector, Channel A+B, provides outputs for both
Channel A and Channel B. This output is useful when
wiring the amplifier for bridged mono operation. See
section 7.4.6. The left Speakon connector provides
an output for Channel B only.

Connect the + and – loudspeaker cables as shown
in the illustrations below.

Channel A and B into two
separate Speakons

Channel A and B into one
Speakon (Stereo and Bi-amp)

Bridge mono

four-channel amplifiers

– Additional connectors

are provided for Channel C and Channel D. Channel
C functions as Channel A above, and Channel D as
Channel B above.

7.4.4 Binding Post (BP) Output connectors

Refer to the instructions in this section if your amplifier
is equipped with Binding Post output connectors.

Binding Post outputs - two-channel models

Binding Post outputs - four-channel models

Connect the positive (+) loudspeaker cable to the
positive (+) red terminals. Connect the negative (-)
loudspeaker cable to the negative (-) black terminals.
For bridge mode, connect the positive (+) terminal
on Channel A to the positive (+) loudspeaker cable
and the negative (-) terminal on Channel B to the
negative (-) loudspeaker cable.

Channels C and D on four-channel versions are
connected in the same manner. For bridge mode,
connect the positive (+) terminal on Channel C to the
positive (+) loudspeaker cable and the negative (-)
terminal on Channel D to the negative (-) loudspeaker
cable.

The outputs on all FP+ Series amplifiers

produce high voltage. Do not connect or

disconnect the loudspeaker cables while the mains
power is on. Never operate the amplifier with any
portion of bare loudspeaker wire exposed. Also,
attach  the  safety  cover  (4-channel  Speakon
versions  only)  on  the  speaker  terminals  for  safe
operation  and  to  comply  with  electrical  product
approvals.

7 OPERATION AND PERFORMANCE

«
...
16
17
18
19
20
...
»

Содержание FP+ Series FP 10000Q
































Отзывы:

Нет отзывов