Lab.gruppen FP+ Series FP 10000Q Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 31

Lab.gruppen FP+ Series FP 10000Q Скачать руководство пользователя страница 13

FP+ Series Operation Manual

13

6.2.3 Input and Output connectors

All FP+ Series amplifiers are equipped with balanced XLR-F input connectors. two-channel models also offer
parallel (“loop-thru”) XLR-M output connectors for daisy-chaining multiple amplifiers from the same signal
source.

All FP+ Series amplifiers except the FP 13000 offer a choice of either binding post (BP) or Neutrik© NL4FC
Speakon output connectors (SP). The FP 13000 is offered with BP connectors only as the potential maximum
output current exceeds the recommended limits for the Speakon connectors.

For specific configuration and wiring information, see section 7.4.

QUICK GUIDE OVERVIEW 6

Audio inputs - four-channel models

Audio inputs and loop-thru connectors -

two-channel models

Speakon outputs - four-channel models

Speakon outputs - two-channel models

Binding Posts - two-channel models

Binding Post outputs - four-channel models

Input connectors

Output connectors

«
...
11
12
13
14
15
...
»

Содержание FP+ Series FP 10000Q
































Отзывы:

Нет отзывов