background image

Mascot ST Tankless Water Heater

Page 33

1

2

3

4

Condensate 

drain pipe

4.15 

Disposal of Condensate

  High efficiency gas condensing Water Heaters create 

condensation when operating. Condensation has 

acidic (pH) of approximately 4-5.

  Condensate must be drained in accordance with all 

local regulations.  Follow your local code with regards 

to the disposal of condensation.

 

 One of 4 disposal methods must be followed

 

1.  to floor drain 

 

2.  to neutralizer drain (optional kit * )

 

3.  to laundry tub

 

4.  to condensate pump (field supplied)

  If a neutralizer is installed, periodic replacement of the 

lime stone (or neutralizing agent) will be required. The 

rate of depletion of the lime stone varies upon usage 

of the Water Heater.

   During the first year of operation, please check the 

neutralizer every few months for depletion.

  Apply only corrosion-resistant materials for the 

condensate drain lines such as 1/2˝ PVC, CPVC, 

Polypropylene pipe or included plastic hose.

   

 

 

NOTICE

Category II & IV water heaters must be installed with a 

means provided for the drainage of condensate.

 

 

     

 

AVIS

Catégorie II & ; IV chauffe-eau doit être installé avec 

une moyens prévus pour l’évacuation des condensats.

 

CAUTION

Condensate is mildly acidic (pH=5), and may harm 

some floor drains and/or pipes, particularly those 

that are metal.  Ensure that the drain, drainpipe, 

and anything that will come in contact with the 

condensate can withstand the acidity, or neutralize 

the condensate before disposal. 

Damage caused by 

failure to install a neutralizer kit or to adequately 

treat condensate will not be the manufacturer’s 

responsibility.

     

Contact Laars to order Kit# A2123601

 

_________________________________________

Содержание MSTWW199

































































Отзывы: