Laars MagnaTherm MGH1600 Скачать руководство пользователя страница 78

Страница: 78 / 116

LAARS Heating Systems

Page 74

3. Press the long Yellow Alert or Yellow Lockout

Bar (the long bar will be a long Grey ‘

History’

Bar if not currently in Alert or Lockout).

Menu 31. OK, Lockouts, Alerts, or Silence.

Choose which history list you would like to see.

OK: brings you back to the status summary screen.
LOCKOUTS brings you to a list of the last 15

lockout events.

ALERTS brings you to a list of the last 15 alerts.
SILENCE allows you to silence an alarm.

From here you can select ‘OK’ to back out of current

screen or ‘Lockouts’ to bring up a list of the

last 15 Lockout occurances. Press ‘Alerts’ to

bring up a list of the last 15 Alerts, and ‘Silence

Alarm’ in the event of a lockout condition.

By silencing the alarm, the audible alert has

been disabled. However, the Lockout is still

active. Reset of the control is needed once the

condition has been repaired.

If you choose ‘ALERTS’, this menu will appear.

Menu 32. Alert History

If you choose ‘LOCKOUTS’, this menu will appear.

Menu 33. Lockout History

4. You can see more detailed information of an alert

or lockout by touching the special entry on the

screen.

Menu 34. Lockout History (showing selected)

Note: The most recent Lockout or Alert will be at

the top of the menu list.

Menu 35. Lockout Detail

Return back to the Status Summary Menu by

pressing the ‘Back’ arrow.

Содержание MagnaTherm MGH1600





















































































































Результаты поиска

Содержание MagnaTherm MGH1600

Отзывы:

Laars MagnaTherm MGH1600, Инструкция по установке и эксплуатации, Страница: 78 / 116

Результаты поиска

Содержание MagnaTherm MGH1600

Отзывы: