La Spaziale S1Dream-T Скачать руководство пользователя страница 13

S1 Dream-T Espresso Machine

 

 

Owner’s Manual 

Page 12 

 

Tamping

 -

 After filling the basket with coffee then use your tamper to apply 30lbs of 

pressure evenly on the coffee bed. Then without applying any pressure lightly twist the 
tamper on the bed of coffee to “polish” the loose grounds on top. Then lock the portafilter 
firmly into the group head and then press either shot button. It is very important to tamp 
consistently with the same pressure each time or your shot quality and timing will vary.  

The grind

 -

 

Adjust your grind so that when you activate the pump, the flow of coffee coming 

out of the portafilter spout looks like the tapered tail of a mouse. It should take 
approximately 25 seconds for a 2 oz. double shot. If it is coming out quicker then the grind 
needs to be adjusted finer, if it is coming out slower or not at all then the grind should be 
adjusted coarser. The grind particle size should look in between powder and salt. Not as 
fine as powder, but not as coarse as salt. Getting the right grind is crucial to making 
delicious espresso with thick rich crema. 

Consistency 

-

 

The quantity of ground coffee and tamping pressure should always be the 

same. Using more or less coffee or tamping lighter or harder will greatly affect the outcome 
and timing of the shot. If the shots are not coming out properly then the only variable that 
should be changed is the grind.  

Cooling Flush 

-

 

A cooling flush is not needed on a dual boiler machine and may actually 

ruin the temperature stability of the shot and is not recommended for optimal performance. 

Cleaning Tip:

 Get into the habit of disposing of the spent grounds immediately after brewing 

espresso.  After disposing of the grounds, return the portafilter to the group head and raise 
the brew lever for a few seconds to rinse away excess oils and loose grounds. By regularly 
following this procedure, you will greatly reduce the tar-like buildup on the shower screen 
that occurs if you allow coffee oils to dry and bake on the hot group. 

For espresso brewing tips check out our video here: 

http://vimeo.com/48819669

  

 

 

Содержание S1Dream-T























Отзывы: