manualshive.com logo in svg
background image

WARNING

Fire and Explosion Hazard

Not for home or recreational vehicle use.

Installation of this brooder in a home or

recreational vehicle may result in a fire or

explosion.

Fire or explosions can cause property

damage or loss of life.

FOR YOUR SAFETY

If you smell gas:

1. Open windows.

2. Don't touch electrical switches.

3. Extinguish any open flame.

4. Immediately call your gas supplier.

FOR YOUR SAFETY

Do not store or use gasoline or other

flammable vapors and liquids in the vicinity of

this or any other appliance.

WARNING

Fire and Explosion Hazard

Keep solid combustibles a safe distance

away from the brooder.

Solid combustibles include wood or paper

products, feathers, straw, and dust.

Do not use the brooder in spaces which

contain or may contain volatile or airborne

combustibles.

Volatile or airborne combustibles include

gasoline, solvents, paint thinner, dust

particles or unknown chemicals.

Failure to follow these instructions may

result in a fire or explosion.

Fire or explosions can lead to property

damage, personal injury or loss of life.

GENERAL  HAZARD  WARNING

Failure to comply with the precautions and instructions provided with this brooder, can result

in:

— Death

— Serious bodily injury or burns

— Property damage or loss from fire or explosion

— Asphyxiation due to lack of adequate air supply or carbon monoxide poisoning 

— Electrical shock

Read this Owner’s Manual before installing or using this product.

Only properly-trained service people should repair or install this brooder.

Save this Owner’s Manual for future use and reference.

Owner’s Manuals and replacement labels are available at no charge.  For assistance, contact

L.B. White at 800-345-7200.

WARNING

Proper gas supply pressure must be provided to the inlet of the brooder.

Refer to rating plate for proper gas supply pressure.

Gas pressure in excess of the maximum inlet pressure specified at the brooder inlet can cause

fires or explosions.

Fires or explosions can lead to serious injury, death, building damage or loss of livestock.

Gas pressure below the minimum inlet pressure specified at the brooder inlet may cause

improper combustion.

Improper combustion can lead to asphyxiation or carbon monoxide poisoning and therefore

serious injury or death to humans and livestock.

2

Содержание I17





























Отзывы: