background image

Contact your local L.B. White dealer for replacement parts

and service or call the L.B. White Company, Inc. at 

(608) 783-5691 for assistance.  Be sure that you have your

heater model number and configuration number when

calling.

30

L.B. White Co., Inc. warrants that the component parts of its

equipment are free from defects in material and

workmanship, when properly installed, operated, and

maintained in accordance with the Installation and

Maintenance Instructions, safety guides and labels

contained with each unit.  If, 

within 12 months from the

date of purchase by the end user

, any component is found

to be defective, L.B. White Co., Inc. will at its option, repair 

or replace the defective part or equipment, with a new part

or equipment, F.O.B., Onalaska, Wisconsin.  

A warranty card on file at L.B. White will automatically

qualify a unit and its component parts for warranty

consideration.  If a warranty card is not on file, a copy of the

bill of sale will be required to establish warranty

qualification.  If neither is available, the warranty period will

be 12 months from date of shipment from L B. White.  

Warranty Policy

Replacement Parts and Service

EQUIPMENT

PARTS

L.B. White Co., Inc. warrants that replacement parts

purchased from the company and used on the appropriate

L. B. White equipment are free from defects both in material

and workmanship for 

12 months from the date of

purchase by the end user

. Warranty is automatic if a

component is found defective within 12 months of the date

code marked on the part.  If the defect occurs more than 12

months later than the date code but within 12 months from

the date of purchase by the end user, a copy of a bill of sale

will be required to establish warranty qualification. 

The warranty set forth above is the exclusive warranty

provided by L.B. White, and all other warranties, including

any implied warranties or merchantability or fitness for a

particular purpose, are expressly disclaimed.  In the event

any implied warranty is not hereby effectively disclaimed

due to operation of law, such implied warranty is limited in

duration to the duration of the applicable warranty stated

above.  The remedies set forth above are the sole and

exclusive remedies available hereunder.  L.B. White will not

be liable for any incidental or consequential damages

directly or indirectly related to the sale, handling or use of

the equipment, and in any event L.B. White's liability in

connection with the equipment, including for claims based

on negligence or strict liability, is limited to the purchase

price.  

Some regions do not allow limitations on how long an

implied warranty lasts, so the above limitation may not

apply to you.  Some regions do not allow the exclusion or

limitation of incidental or consequential damages, so the

above limitation or exclusion may not apply to you.  This

warranty gives you specific legal rights, and you may also

have other rights which vary from region to region.

Содержание AW230































Отзывы: