background image

WARNING

Fire and Explosion Hazard

Not for home or recreational vehicle use.

Installation of this heater in a home or

recreational vehicle may result in a fire or

explosion.

Fire or explosions can cause property

damage or loss of fire.

FOR YOUR SAFETY

If you smell gas:

1. Open windows.

2. Don't touch electrical switches.

3. Extinguish any open flame.

4. Immediately call your gas supplier.

FOR YOUR SAFETY

Do not store or use gasoline or other

flammable vapors and liquids in the vicinity of

this or any other appliance.

WARNING

Fire and Explosion Hazard

Keep solid combustibles a safe distance

away from the heater.

Solid combustibles include wood or paper

products, feathers, straw, and dust.

Do not use the heater in spaces which

contain or may contain volatile or airborne

combustibles.

Volatile or airborne combustibles include

gasoline, solvents, paint thinner, dust

particles or unknown chemicals.

Failure to follow these instructions may

result in a fire or explosion.

Fire or explosions can lead to property

damage, personal injury or loss of life.

GENERAL  HAZARD  WARNING

Failure to comply with the precautions and instructions provided with this heater, can result in:

— Death

— Serious bodily injury or burns

— Property damage or loss from fire or explosion

— Asphyxiation due to lack of adequate air supply or carbon monoxide poisoning 

— Electrical shock

Read this Owner’s Manual before installing or using this product.

Only properly-trained service people should repair or install this heater.

Save this Owner’s Manual for future use and reference.

Owner’s Manuals and replacement labels are available at no charge.  For assistance, contact

L.B. White at 608-783-5691.

WARNING

Proper gas supply pressure must be provided to the inlet of the heater.

Refer to the heater’s dataplate for proper gas supply pressure.

Gas pressure in excess of the maximum inlet pressure specified at the heater inlet can cause

fires or explosions.

Fires or explosions can lead to serious injury, death, building damage or loss of livestock.

Gas pressure below the minimum inlet pressure specified at the heater inlet may cause

improper combustion.

Improper combustion can lead to asphyxiation or carbon monoxide poisoning and therefore

serious injury or death to humans and livestock.

2

Содержание AW230































Отзывы: