Kyocera KM-2560 Скачать руководство пользователя страница 71

Страница: 71 / 392

2H0/2HZ

1-3-35

U073

Checking scanner operation
Description

Simulates the scanner operation under arbitrary conditions.

Purpose

To check scanner operation.

Start

1. Press the start key.
2. Select the item to be operated.

Setting: SCANNER MOTOR

1. Select [SCANNER MOTOR].
2. Select the item.
3. Change the setting using the +/- keys.

Original sizes for each setting in SIZE

4. Press the start key. Scanning starts under the selected conditions.
5. To stop operation, press the stop key.

Method: HOME POSITION

1. Select [HOME POSITION].
2. Press the start key.

The mirror frame of the scanner moves to the home position.

Method: DP READING

1. Select [DP READING].
2. Press the start key.

The mirror frame of the scanner moves to the reading position.

Method: DUST CHECK

1. Select [DUST CHECK].
2. Press the start key. The exposure lamp lights.
3. To turn the exposure lamp off, press the stop key.

Completion

Press the stop key when scanning stops. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Display

Description

SCANNER MOTOR

Scanner operation

HOME POSITION

Home position operation

DP READING

DP scanning position operation

DUST CHECK

Dust adhesion check operation with lamp on

Display

Operating conditions

Setting range

ZOOM

Magnification

25 to 400 %

SIZE

Original size

See below.

LAMP

On and off of the exposure lamp

0 (off) or 1 (on)

Setting

Paper size

Setting

Paper size

5000

A5R

4300

7800

Folio

5100

11" x 8

1/2

10200

11" x 17"

10000

9000

11" x 15"

8600

8400

1/2

" x 14"

7100

A4R

6600

1/2

" x 11"

6100

B5R

5100

1/2

" x 8

1/2

Содержание KM-2560









































































































































































































































































































































































































Результаты поиска

Содержание KM-2560

Отзывы:

Похожие инструкции для KM-2560

Бренды по названию

Популярные бренды

Kyocera KM-2560, Руководство по обслуживанию

Результаты поиска

Содержание KM-2560

Отзывы:

Похожие инструкции для KM-2560

Бренды по названию

Популярные бренды