manualshive.com logo in svg

KYMCO X-Town 300, Руководство пользователя

Поделиться
Скачать
KYMCO X-Town 300 Скачать руководство пользователя страница 62

 

 

MAINTENANCE

 

Tires Inspection 

Tire wear changes the tire profile and may 
affect the vehicle

’s handling characteristics. 

Check the tire condition before each riding. 
Replace the tires if tread depth is less than 
the following limit: 

 

Minimum tread depth: 

Front: 0.8 mm (0.03 in) 
Rear:  0.8 mm (0.03 in) 
 

▆

NOTE:

 Measure the tread depth 

①

, do not 

judge by a visual inspection. 

 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

 

▆

NOTE:

 Be sure to balance the wheel after 

repairing a puncture or the tire. Proper wheel 
balance is important to avoid variable contact 
between tire and ground, and to avoid uneven tire 
wear. 
 

 

▆

NOTE: 

Replace the tires if there

’s visual 

evidence of damage as cracks or cuts. 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

   

WARNING 

An improperly repaired, installed, or 
balanced tire can cause you to lose 
control of your scooter or shorten tire life. 
Ask the authorized KYMCO dealer, or a 
qualified tire shop to perform tire repair, 
replacement, and balancing due to the 
proper tools and experience are required. 
Always install tires according to the 
rotation direction shown by arrow on the 
sidewall of each tire. 

1

2 

44 

Содержание X-Town 300






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды