manualshive.com logo in svg

KYMCO X-Town 300, Руководство пользователя

Поделиться
Скачать
KYMCO X-Town 300 Скачать руководство пользователя страница 23

 

 

CONTROLS & FEATURES

 

Adjust clock

 

 

The setting procedure:

 

1.  Turn the ignition switch to the ON position.  
 
2.  Push  the  MODE  button  for  more than 2 
seconds to select the ODO mode.

 

 

 

▆

NOTE: 

The d

igital clock can be only adjusted in ODO 

mode. 

 
3. Push the MODE button for more than 2 
seconds. 

The “hour” digits will be flashing and 

the hour can be adjusted at that moment. 
 
 
 
4. Push the RESET  button to set the hour. 

 
 
 
 
 

 
14 

 

5. Push the MODE button; it will change to 
make 

the “minute” digits be flashing. 

 
 
 

6. Push the RESET  button to set the minute. 

 
 
 

7. Push both the MODE and RESET buttons at 
the same time to finish the clock setting. 

 
 
 
 

 

▆

NOTE:

 The adjustment will be cancelled if any 

button is not pressed within approximately ten 
seconds. 
 

 

▆

NOTE:

 The clock will be reset to 12:00 when the 

battery is disconnected. 
 
 

Содержание X-Town 300






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды