KYMCO X-Town 300 Скачать руководство пользователя страница 2

Страница: 2 / 69

Read this manual carefully.

This Owner

’s Manual contains important information on safety, operation and maintenance of KYMCO

X-

Town

300

. Anyone who is going to ride should carefully read and understand the contents of this manual

before riding. For personal safety, understand and follow all of the warnings contained in this Owner

’s

Manual and the labels attached on vehicle. This Owner

’s Manual should be considered a permanent

part of the vehicle, keep it with the motorcycle. ON-ROAD USE ONLY for this motorcycle.

Particularly important information is provided in this manual by the following
symbols and signal words:

The SAFETY ALERT symbol means ATTENTION! BE ALERT!

YOUR SAFETY CAN BE AFFECTED.

WARNING

CAUTION

Failure to follow these instructions can result in severe injury or death.

These instructions point out the special precautions must be
followed to avoid damage.

▆

NOTE:

The NOTE indicates the additional important information.

Содержание X-Town 300






































































Результаты поиска

Содержание X-Town 300

Отзывы:

Бренды по названию

Популярные бренды

KYMCO X-Town 300, Руководство пользователя

Результаты поиска

Содержание X-Town 300

Отзывы:

Бренды по названию

Популярные бренды