manualshive.com logo in svg

KYLAND KIEN8000, Руководство пользователя

Поделиться
Скачать
KYLAND KIEN8000 Скачать руководство пользователя страница 32

Section   5: 
Testing 
Methods

1.13

Self-Check

When the power is connected, all service indicators(except for POWER OUT) on the 

front panel will flash one time, which means normal running of these ports. Later on, 

the RUN indicator is on.

1.14

Testing Ethernet Ports

As shown in Figure 5-1, KIEN8000 is powered up and any two Ethernet ports are 

connected to the uplink Ethernet ports of KIEN1000-PD(powered device) by cross-

over or straight-through cables. Any port of the PD is connected to the Ethernet port of 

PC. Ping command is sent while they can be ping each other without packet loss. 

Meanwhile, the 10/100M light of KIEN8000 should be always on and LNK/ACT light 

is blinking, POWER OUT is always on. All these can prove the tested hardware is 

working normally. The same way is used for other Ethernet ports (Please refer to the 

example for PING command operation).

测试计算机2

测试计算机1

Figure 5-1  Testing Ethernet Ports

-

22

-

Содержание KIEN8000







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды