KwiKool KPHP Series Скачать руководство пользователя страница 16

Page 14

System trips breaker on 
start up

Incoming power is incorrect, 
breaker is undersized or 
faulty, and/or  extension 
power cable is too long and 
or undersized.

Verify the circuit and power 
cable is within the systems 
specifications, consult with 
your electrician or call 
1-800-KwiKool for 
guidance.

System starts up and 
operates in the chosen 
mode but the condenser 
discharge air exhaust fan 
stops and starts in cool 
mode or in heat mode the 
supply air fan starts and 
stops.

Normal operating condition 
especially in low tempera-
tures.

No action required, see 
sections IV C. 2 & 3

Note:

 To avoid excessive 

fan cycling, return air must 
not be below the specifica-
tions of your KwiKool 
system.

Supply air flow is limited, and 
or water is dripping from the 
front of the system

Supply or return air is 
blocked or restricted, and or 
the evaporator coil is 
freezing. 

Verify that supply and 
return air are not blocked 
and duct work is installed 
to specification, remove or 
add duct as needed, check 
air filter for blockage.

Fault

Possible Cause

Possible Solution

Display shows 

32

 and unit 

will not turn on cooling.

No connection of tempera-
ture sensor to Micropro-
cessor. Temperature 
Sensor malfunction.

Call 1-800-KwiKool for 
instructions.

Condensate is not pumping.

Water is below pumping  
level, external line 
restricted, line installed with 
too high of lift.

Reservoir fills, and then 
pumps. Check for line 
crimping or restrictions and 
proper line run height. Refer 
to the user guide Section 5: 
Built in Safeguards.

Evaporator coil is freezing

Low or restricted air flow. 
Undersized capacity, unit 
constantly on, unable to 
achieve set point. Low 
return air temperature out 
of factory specifications. 
Evaporator door open, 
mechanical system 
malfunction.

Direct supply return air to 
area of highest heat load, 
check for blocked air flow 
from the supply air, replace 
air filters, adjust set point to 
allow the unit to cycle, add 
another KwiKool system or 
larger capacity model, close 
evaporator compartment 
door. Install service gauges 
to view pressures.
Call 1-800-KwiKool

Содержание KPHP Series



















Отзывы: