Kval ON-3V Скачать руководство пользователя страница 57

Страница: 57 / 72

Staging Area Controls

3-9

KVAL Manual

Staging Area Controls

Controls are located at the door placement area. The controls are designed for safety during the

operation of the machine. The controls can pause the machine to allow safe entry, disable the lift,

reset the lift, and apply emergency stop. In addiction to controls, a Light Safety Curtain protects

the entrance to the placement area.

Note:

See “Staging Area Controls” on page 2-11

, for further descriptions of the Stag

ing Controls.

FIGURE 3- 8.

Staging Area Controls

Request Access Button:

Press to enter the staging

area safely. Mainly to load

doors to be processed.

Reset Light Button:

If the light curtain is broken,

press to reset the safety cir

cui

Pause/Resume Lift:

Press the Pause/Resume

Button to disable or pause the

process cycle. To resume the

process, push the button

again.

Emergency Stop:

Press the Emergency button

to stop machine. Will maintain

clamp and lift. To restart

machine,

see “Shut Down

and Recovery” on page 2-8.

Содержание ON-3V









































































Результаты поиска

Содержание ON-3V

Отзывы:

Бренды по названию

Популярные бренды

Kval ON-3V, Руководство по эксплуатации

Результаты поиска

Содержание ON-3V

Отзывы:

Бренды по названию

Популярные бренды