Kval ON-3V Скачать руководство пользователя страница 10

Страница: 10 / 72

Overview of the ON-3V

1-2

KVAL Manual

Overview of the ON-3V

The

KVAL ON-3V Door Feeder/Stacker

automatically lifts individual doors from a stack and places

the door onto a powered roll table where the door can be fed to the next machine manually with a

'Call Door' switch or automatically fed when the next machine in the line is ready to receive a

door. Cycle time is approximately 20 seconds. The ON-3V can lift and feed flush doors and up to

4ft wide by 8ft high. The door is lifted via a vacuum system which utilizes two vacuum pads to

lift the unit. The lift system will lift doors that vary in height from 6’-6” to 8’-0” without any

adjustment. Door thickness can vary from 1-3/8” to 2-1/4”. Maximum door weight 175lb. A vari

able speed drive is utilized, with controls, to match the feed speed of following Kval equipment,

i.e 558 Door Sizer or Kval Pre-hanging line. Wire guards are attached to the ON-3V frame on

three sides; slot openings allow the door to be manually fed into the feeder as well as fed out to

the next machine.

Note:

Maximum door stack height is 60” from the ground including call board and or

conveyor system.

Note:

Minimum ceiling height required for clearance for the clamp assembly is at

maximum height is 15’-0”.

Available

Options

TABLE 1-1.

Options Available

Option Title

Description

Option L

Raised

Moulded Doors

This option adds the capacity to feed doors with raised moulding on

either or both sides. Maximum moulding height above door face will be

3/4 inch. Spacers used to stack doors must be positioned so they do

not interfere with the clamp system. The clamp system supports must

be manually positioned to clear the moulding prior to feeding the doors.

The feed table will be equipped with additional rubber covered rolls

closely spaced to support the door on the moulding

. Note:

When spec

ifying a line that includes a 558 Sizer, add Option R to the 558 Door

Sizer to also make it capable of feeding doors with raised mouldings.

Option R Door Rotate

Adds rotate capability to the vacuum lifting fixture so doors can rotate

180 degrees as they transfer to the infeed table, or door stack. Touch

screen programming is included to rotate every door, every other door

or one door. PLC inputs are also available to automatically rotate as

part of a down-load process

Option S

Stacker

Option Makes the ON3V a Door Stacker Opposed to Door Feeder.

Option T

Extended Con

trol Cable

Extended cable length required when a supplemental machine is

placed between the door feeder and main machining center. I.e option

is required when the 558 Door Sizer is installed between the ON-3 and

the door pre-hanging machine.

Содержание ON-3V









































































Результаты поиска

Содержание ON-3V

Отзывы:

Похожие инструкции для ON-3V

Бренды по названию

Популярные бренды

Kval ON-3V, Руководство по эксплуатации

Результаты поиска

Содержание ON-3V

Отзывы:

Похожие инструкции для ON-3V

Бренды по названию

Популярные бренды