Kunz AcrEase Pro60K-25HP Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 25

background image

16

I.

LUBRICATION

There are three lubrication points on the wing mower  --  one spring-loaded idler pivot and two
caster wheel pivots.  Lubricate at approximately 10 hr. intervals or more often as required in dusty
conditions.  Lubricate with a high grade of pressure gun grease.

J.

TIRE PRESSURE

To reduce wing mower bounce on rough yards, the front and rear tire pressure can be reduced so
they feel slightly soft (approximately 15 PSI) when they are stepped on.

K.

FUSE LOCATION

This particular mower comes equipped with a 10 AMP mini blade type fuse. The fuse is located
behind the ignition switch/control panel in a black rubber inline fuse holder.

L.

TRANSPORTATION OF MOWER

When transporting the mowers between jobs turn off the fuel shut-off valve. The fuel shut-off
valve is located below the fuel tank.

M.

STORAGE

Turn off the fuel shut off valve (red colored rotating knob) located inline on the fuel hose. The

off

position on the valve is when the red handle lines up with the “O” symbol.

If the mower is stored

outside, the engine should be covered to prevent water from getting inside the engine during
heavy rainstorms. See the Engine Manual for additional information.

N.

EPA EVAPORATIVE COMPONENTS

This mower has been designed and built to meet all current EPA regulations.  Any modification to
the fuel tank, fuel lines, vapor hose, fuel cap, roll-over / fuel vapor valve, carbon canister
(California Only) and hose clamps are prohibited.  Replacement evaporative components should
be purchased from Kunz Engineering.  Any questions about EPA regulations or evaporative
components can be directed to Kunz Engineering Inc. at 815-539-6954.

«
...
16
17
18
19
20
...
»

Содержание AcrEase Pro60K-25HP


























Отзывы:

Нет отзывов

Похожие инструкции для AcrEase Pro60K-25HP

Бренд: Partner Страницы: 10

Бренд: Partner Страницы: 76

Бренд: Sears Страницы: 37

Бренд: Lastec Страницы: 56

Hydrostatic Vergecutter 76

Бренд: Ransomes Страницы: 54

Бренд: Poulan Pro Страницы: 42

Бренд: AL-KO Страницы: 304

Бренд: Murray Страницы: 52

Бренд: Craftsman Страницы: 88

Бренд: Murray Страницы: 68

Бренд: Electrolux Страницы: 20

Бренд: Electrolux Страницы: 6

Бренд: Craftsman Страницы: 68

Бренд: Craftsman Страницы: 76

28813 - 46 in. Lawn Tractor

Бренд: Craftsman Страницы: 68

Бренд: Craftsman Страницы: 72

Бренд: Craftsman Страницы: 76

Бренд: Craftsman Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды