KUHN GMD16 Скачать руководство пользователя страница 64

Страница: 64 / 100

GMD16-GMD20

9. - Optional equipment

KN225BGB_A

Disc mower

9.9.1 Coupling and uncoupling



Preparing the machine

- Remove filler plug (1) and its washer.
- Pour the correct oil quantity and quality through the

opening of the filler plug:
• 1 L (0.27 US gal) of high-performance hydraulic

oil.

- Clean and reinstall filler plug (1) and its washer.



Hydraulic connection

- No hydraulic start up to be done before using the

machine.



Uncoupling the machine

- No hydraulic start up to be done before using the

machine.

9.9.2 Putting the machine into transport

position

- Fully turn thumbwheel (1) clockwise.
- Position lever (2) in position (a).
- Activate hydraulic pump control lever to place the

mowing unit in transport position.

The machine automatically locks in transport
position.

- Place lever (2) in its holder (3).

The machine is in transport position.

Never engage the tractor PTO drive when the
machine is in transport position.

Содержание GMD16





































































































Результаты поиска

Содержание GMD16

Отзывы:

Похожие инструкции для GMD16

Бренды по названию

Популярные бренды

KUHN GMD16, Руководство оператора

Результаты поиска

Содержание GMD16

Отзывы:

Похожие инструкции для GMD16

Бренды по названию

Популярные бренды