manualshive.com logo in svg

KUHN EL82, Руководство оператора

Поделиться
Скачать
KUHN EL82 Скачать руководство пользователя страница 32

Power tiller

30

EL82

Putting into service

Adjusting the category

- Loosen screw (1).
- Remove the 2 nuts (3).
- Position lower coupling yokes (4) opposite free holes.
- Tighten the 2 nuts (3).

• Torque: 21 daN m (155 lbf ft).

- Adjust sliding guard (2) position to fully cover machine

front part between lower coupling yokes and machine
ends.
• Distance D between sliding guard and lower

coupling yokes must not exceed 60 mm (2.4’’).

- Tighten screw (1).

• Torque: 8.5 daN m (63 lbf ft).

- Proceed the same way on the other side.

Coupling the machine

- Park the machine on an even fairly level ground.
- Lower the tractor three-point linkage.
- Insert lower hitch pins and secure them with lynch

pins.

- Attach the top link to the hitch pin.
- Secure hitch pin with lynch pin.
- Adjust the top link length so that the machine is

horizontal with regards to the ground.

4

3

2

1

3

D

Содержание EL82









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды