background image

74

TROUBLESHOOTING

ENGLISH

If you have any questions, contact your local KUBOTA Dealer.

Engine stops suddenly.

A

Insufficient fuel.

A

Refuel.

A

Check the fuel valve position.

A

Check the carburetor fuel valve
position.

Rough engine running.

A

Spark plug defective.

A

Adjust the spark plug gap or replace it.

A

Spark plug wire defective.

A

See your Kubota dealer.

A

Carburetion problems.

A

See your Kubota dealer.

A

Ignition coil defective.

A

See your Kubota dealer.

A

Choke is adjusted incorrectly.

A

Adjust choke cable.

A

Fuel hose or fuel filter clogged or
damaged.

A

Clean or replace fuel lines, and see
your Kubota dealer.

A

Improper or stale fuel.
(Fuel quality is poor.)

A

Replace fuel and the fuel filter.

A

Air cleaner is clogged.

A

Clean or replace the air cleaner.

Exhaust fumes are colored.
(Black, Dark or Gray)

A

Overload.

A

Reduce load.

A

Low grade fuel is used.

A

Use specified fuel.

A

Fuel filter is clogged.

A

Replace the fuel filter.

A

Air cleaner is clogged.

A

Clean or replace the air cleaner
element.

A

Choke is not fully opened.

A

Check the choke position.

Exhaust fumes are colored.
(White or Blue)

A

Excessive engine oil.

A

Reduce to the specified oil level.

A

Piston ring is worn or stuck.

A

See your Kubota dealer.

Engine overheats.

A

Engine is overloaded.

A

Lower speed or reduce load.

A

Engine oil is insufficient.

A

Replenish engine oil.

A

Engine air intake screen and cooling
fins are dirty.

A

Clean the air intake screen and cooling
fins.

A

Air cleaner element is plugged.

A

Clean or replace the air cleaner
element.

A

Engine speed is too low.

A

Operate at the "FAST" speed.

A

Operating ground speed is too fast.

A

Operate the machine at the slower
ground speed.

Engine knocks.

A

Stale or low octane fuel.

A

Use specified fuel.

A

Engine overloaded.

A

Lower ground speed or reduce load.

A

Engine speed is too low.

A

Operate at the "FAST" speed.

Engine will not idle.

A

Spark plug defective.

A

Adjust the spark plug gap or replace it.

A

Faulty spark plug.

A

Replace the spark plug.

A

Carburetion problem.

A

See your Kubota dealer.

Symptom (If)

Cause

Remedy

Содержание Z723
































































































Отзывы: