Kubota Z723 Скачать руководство пользователя

Страница: 83 / 95

ADJUSTMENT

ENGLISH

5. Tighten the nut on the bottom side of damper.
6. Perform steps 1 through 5 for both motion control

levers.

MAXIMUM SPEED (FORWARD)

Consult your local KUBOTA Dealer for this service.

MOTION CONTROL LEVER ALIGNMENT

Check the alignment

Check the gap and space between the levers, at the
maximum forward position.

If positions of the control levers are unequal, an
adjustment is necessary.

To avoid serious injury:

Park the machine on a firm and level surface.

Stop the engine, remove the key and apply the
parking brake.

Aligning the control levers

1. Stop the engine and apply the parking brake.

Lever position (High or Low)

2. Remove the bolts and select the motion control lever

position, high or low.

3. Tighten the bolts.

Lever alignment (Right and Left)

4. Loosen the bolts.
5. Slide both levers forward or rearward to the desired

position within tab slots until levers are aligned.

6. Tighten the bolts.

Recommendation

Gap: 0 to 2 mm

(0 to 0.08 in.)

(A) "GAP"

(1) Bolt
(2) Flange nut
(3) Tab slot

(A) High position

Содержание Z723
































































































Результаты поиска

Содержание Z723

Отзывы:

Похожие инструкции для Z723

Бренды по названию

Популярные бренды

Kubota Z723, Руководство оператора

Результаты поиска

Содержание Z723

Отзывы:

Похожие инструкции для Z723

Бренды по названию

Популярные бренды