background image

15

OPERATING THE ENGINE

ENGLISH

A

When the ambient temperature is less than -15
(5

), remove the battery from the machine and store

it somewhere warm until the next operation.

CHECK DURING OPERATING

While operating, make the following checks to see that all
the parts are functioning normally.

B

Immediately Stop the Engine if:

A

The engine suddenly slows down or accelerates.

A

Unusual noises are suddenly heard.

A

Exhaust fumes suddenly become discolored.

B

Easy Checker (TM)

If the warning lamps in the Easy Checker (TM) come on
during operation, stop the engine immediately, and find
the cause as shown below.
Never operate the machine while Easy Checker (TM)
lamp is "ON".

Engine oil pressure

If the oil pressure in the engine goes below the
prescribed level, the warning lamp in the Easy
Checker (TM) will come on.

If this should happen during operation, stop the
engine immediately and check level of engine oil.

B

Fuel Gauge

The fuel gauge indicates the fuel level.

A

Do not refuel over "F". Fill the tank only to the bottom
of the filler neck in the fuel tank.

A

Fill the fuel on a level ground.

B

Hour Meter

This meter gives readings for the hours the machine has
been operated for.

A

As the hour meter works electrically, it starts to work
when the key switch is turned to "ON", regardless of
the engine running or not.

8.

Make sure that the Easy Checker (TM) 
lights have gone off. If the light is still 
on, immediately stop the engine and 
check the remedy following the 
instruction. (See "CHECK DURING 
OPERATING" in "OPERATING THE 
ENGINE" section.)

9

.

Warm the engine by running at medium 
speed.

(1) Easy checker (TM)

(1) Fuel gauge

(E) "EMPTY"
(F) "FULL"

(1) Hour meter

Содержание Z723
































































































Отзывы: