7
Section 1: Assembly & Set-up
AP-SRT62, & AP-SRT76 Rotary Tillers 321-095MK
7/31/17
Skid Steer Requirements
The Rotary Tiller is designed to attach to skid steer
loaders with the following minimum requirements:
SAE lift capacity . . . . . . . . . . . . . . . . . . . . . . 1200 lbs.
Hitch type . . . . . . . . . . . . . . . . . Universal Quick Hitch
Hydraulic flow rates
SRT62 low flow . . . . . . . . . . . . . . . . . . 14 - 23 gpm
SRT62 & SRT76 high flow . . . . . . . . . . 23 - 40 gpm
Hydraulic pressure rates (min. - max. psi)
SRT62 low flow motor . . . . . . . . . . . 2800 - 4500 psi
SRT62 high flow motor . . . . . . . . . . 2000 - 4500 psi
SRT76 high flow motor . . . . . . . . . . 2300 - 4500 psi
Hydraulic hoses . . . . . . . . . . . . . 2 - Hydraulic outlets
Case drain hose . . . . . . . . . . . . . . 1 - Hydraulic outlet
Skid steer weight . . . . . . . . . . . . . See warning below
!
WARNING
To prevent serious injury or death:
Torque Requirements
See
“Torque Values Chart”
on page 28 to determine
correct torque values when tightening hardware.
Rotary Tiller Lifting Points
Refer to Figure 1-1:
The tiller is provided with four lifting points to hook a sling
chain. See arrows in Figure 1-1 for location of lifting
points.
IMPORTANT:
Skid steer must be equipped with a
case drain system.
IMPORTANT:
The tiller is capable of throwing
product inside the cab when top of tiller hitch is
rotated forward to the 2" depth setting and tines are
set to operate rotating in the direction that will kick
product towards the cab. In this situation, Kubota
recommends using a protective door to protect
operator from thrown objects.
A universal Operator Protective Door is available
from Kubota or use a protective door provided by
your skid steer manufacture. Refer to
additional information.
Dealer Preparations
!
CAUTION
To avoid serious injury:
Securely support tiller on jack stands or support blocks.
This tiller is shipped almost completely assembled. To
speed up assembly task and to make the job as safe as
possible, the following should be completed:
•
Speed up assembly tasks and make the job safer by
having all needed parts and equipment readily at hand.
•
Read and understand the Operator’s Manual. An
understanding of how it works will aid in the assembly
and setup.
•
Go through the
Pre-Assembly Checklist
below
before assembling the Rotary Tiller.
Rotary Tiller Lifting Points
Figure 1-1
Pre-Assembly Checklist
Check
Ref.
Make sure miscellaneous assembly tools are on hand.
Have a forklift or hoist with properly sized chains and safety
stands on hand capable of lifting 2500 lbs.
Have a minimum of two people available during assembly.
Check to see if ballast is needed for the skid steer.
See Specifications on page 26 for unit weights.
Make sure all major components and loose parts
are shipped with the attachment.
Operator’s
Manual
Double check to make sure all fasteners & pins
are installed in the correct location. Refer to the
Parts Manual if unsure.
NOTE: All assembled hardware from the factory
has been installed in the correct location.
Remember location of a part or fastener if
removed. Keep parts separated.
Operator’s
Manual
and
Parts Manual
Make sure working parts move freely, bolts are
tight and cotter pins are spread.
Operator’s
Manual
Make sure all grease fittings are in place and
lubricated.
Make sure all safety labels are correctly located
and legible. Replace if damaged.
Important
Safety
Information
37802
Section 1: Assembly & Set-up
Содержание AP-SRT62
Страница 35: ......
