Kubota AP-SC6072 Скачать руководство пользователя страница 19

Страница: 19 / 42

Section 1: Assembly & Set-up

Table of Contents

AP-SC6072 Skid Cutter 327-321MK

4/6/21

Hydraulic Hose Hook-Up

Refer to Figure 1-1 on page 13:

WARNING

To avoid serious injury or death:

•

Shut power machine down and release all hydraulic

pressure to the equipment before connecting or

disconnecting hydraulic hoses to or from the power

machine.

•

Hydraulic fluid under high pressure will penetrate the skin

and/or eyes causing a serious injury. Wear protective gloves

and safety glasses or goggles when working with hydraulic

systems. Use a piece of cardboard or wood rather than

hands when searching for leaks. A doctor familiar with this

type of injury must treat the injury within a few hours or

gangrene may result. DO NOT DELAY.

Refer to Figure 1-5:

1. If attaching to a Kubota SVL75 machine, be sure to

route hydraulic hoses through hose loop (#1) on the

left side of the cutter hitch as shown.

Hose Route For Kubota SVL Machine

Figure 1-5

Refer to Figure 1-1 on page 13:

2. Thread hoses through any hose holders that may be

helpful on the machine operating the cutter. See your

skid steer Operator’s Manual for instruction on how to

use these hose holders.

3. Connect male and female couplers on the cutter to

the appropriate skid steer flat faced couplers.

4. Connect cutter case drain coupler to skid steer case

drain coupler.

IMPORTANT:

The customer must select best way to

route the hydraulic hoses. Make sure the hoses will

not contact the skid steer wheels or tracks. See

“Equipment Clearances”

on page 17

for detailed instructions on how to check for

clearances.

NOTE:

Use of Kubota’s SVL Hose Stay is not

recommended for this attachment.

70030

Do not use

SVL hose stay

5. Operate skid steer to check blade rotation. The SC60

is designed to have cutter blades rotate clockwise

when looking down at the deck.

6. Zip tie hydraulic hoses together every 2 feet from

male and female couplers.

Protective Door Assembly (Optional)

Refer to Figure 1-6:

WARNING

To avoid serious injury or death:
Do not drill holes in the ROPS (Roll Over Protection System)

to attach this Operator Protective Door. Drilling unapproved

holes in the ROPS can weaken the structure.

For your safety, do not use this cutter without an installed

OEM Polycarbonate Protective Operator Door. If the skid

steer/track loader is not equipped with a polycarbonate

door, an optional door may be purchased with the cutter.
Refer to the instructions below when installing Kubota’s

optional polycarbonate door.
1. Cut notches in protective door as needed to provide

clearance around u-bolts and skid steer frame.

2. Install the polycarbonate door to the skid steer’s

hand hold with two u-bolts (#3), flat bars (#2), and

four nuts (#1) as shown. Tighten nuts to correct

torque.

Polycarbonate Protective Door Assembly

Figure 1-6

Skid steer

hand hold

If needed, locate & cut

notches in door for

U-bolts clearance.

If needed, locate &

cut notch in door to

clear skid steer

frame.

Hook elastic tie-down

to skid steer cage to

keep door closed.

24608

Содержание AP-SC6072











































Результаты поиска

Содержание AP-SC6072

Отзывы:

Бренды по названию

Популярные бренды

Kubota AP-SC6072, Руководство оператора

Результаты поиска

Содержание AP-SC6072

Отзывы:

Бренды по названию

Популярные бренды