ENGLISH
26
In the event that the motorcycle is also used in winter and on roads where one has to expect salt spraying, you will have to take pre-
cautions against the aggressive road salt.
– clean motorcycle thoroughly and let it dry
– treat engine, carburetor, swing arm, and all other bare or galvanized parts (except for brake discs) with a wax-based anti-corrosion
agent.
W A R N I N G
K
EEP ANTI
-
CORROSION AGENT FROM GETTING INTO CONTACT WITH THE BRAKE DISCS
,
FOR OTHERWISE THIS WILL SIGNIFICANTLY REDUCE THE BRAKING
POWER
.
!
CAUTION
!
A
FTER RIDES ON SALTED ROADS
,
CLEAN MOTORCYCLE THOROUGHLY WITH COLD WATER AND LET IT DRY WELL
!
CONSERVATION FOR WINTER OPERATION
Clean the motorcycle at regular intervals to preserve the outward appearance of the plastic parts.
The best manner would be to use warm water that has been mixed with a normal trade washing detergent and a sponge. The hard
dirt can be removed before with the help of a soft water jet.
!
CAUTION
!
N
EVER CLEAN YOUR MOTORCYCLE WITH A HIGH
-
PRESSURED CLEANER OR A HIGH
-
PRESSURED WATER JET
. T
HE WATER COULD OTHERWISE RUN INTO THE
ELECTRICAL COMPONENTS
,
CONNECTORS
,
SHEATHED CABLES
,
BEARINGS
,
CARBURETOR ETC
.
AND CAUSE DISTURBINGS OR LEAD TO A PREMATURE DESTRUC
-
TION OF THESE PARTS
.
– You should use normal trade-mark detergents to clean the engine. Strongly dirted parts should be cleaned additionally with the
help of a paint brush.
– After the motorcycle has been rinsed with a soft water jet, it should be dried by air pressure and a cloth. Then take a short drive
until the engine has reached the working temperature and also use the brakes. Due to the heat, the water also evaporates at the
unapproachable parts of the engine and the brakes.
– Slide back the protective covers on the handlebar-mounted instruments so that any water that may have seeped into this part of
the motorcycle is allowed to evaporate.
– After the motorcycle has cooled down, oil and grease all sliding and pivot points. Treat the chain with a chain spray too.
– To prevent failures in the electric system, you should treat the ignition lock, the emergency OFF switch, light switch and the socket
connectors with contact spray.
CLEANING
Should you desire to make a pause over a longer space of time, please observe the following instructions:
– Clean motorcycle thoroughly (see chapter: CLEANING)
– Check antifreezer and amount of cooling liquid.
– Let the engine warm up again.
– Drain fuel from float chamber of the carburetor. By this means, carburetor jets are prevented from becoming resinous by the old fuel.
– Remove spark plug, and fill approx. 5 ccm engine oil into the cylinder via the spark plug hole. Start for 5 seconds in order to
spread the engine oil, and reinstall spark plug.
– Let fuel flow out of tank into an appropriate container.
– Correct tire pressure.
– Lubricate pivot points of the control levers, foot rests, etc. as well as the chain.
– Servicing the shock absorber linkage and swing arm bearings.
– Remove and charge battery (see chapter: BATTERY).
– The storage place should be dry and not subject to excessive temperature fluctuations.
– Cover the motorcycle with an air permeated tarpaulin or blanket. Do not use non air permeable materials as a possible humidity
might not be able to escape and could cause corrosion.
!
CAUTION
!
I
T IS EXTREMELY BAD TO LET THE ENGINE RUN FOR SHORT PERIODS OF TIME WHEN THE MOTORCYCLE IS KEPT IN STORAGE
. S
INCE IN THIS CASE THE ENGINE
WOULD NOT GET WARM ENOUGH
,
THE STEAM PRODUCED DURING THE COMBUSTION PROCESS WOULD CONDENSE AND CAUSE RUSTING ON CRANKSHAFT
,
MAIN BEARING
,
AND EXHAUST SYSTEM
.
RE-INITIATION AFTER TIME OF STORAGE
– Mount the charged battery (watch out for polarity, RED = +)
– Fill up tank with fresh fuel and turn the fuel tap to the ON position.
– Check motorcycle as before each start.
– Take a short, careful test ride first.
STORAGE
Содержание 125 LC2 1998
Страница 1: ...BEDIENUNGSANLEITUNG OWNER S HANDBOOK MANUEL D UTILISATION 125 LC2 98 ART NR 320531 2 98...
Страница 2: ......
Страница 31: ......
