KSB Etaline-R Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 52

background image

7 Servicing/Maintenance

36 of 52

Etaline-R

7.4 Dismantling the pump set

7.4.1 General information/Safety regulations

WARNING

Unqualified personnel performing work on the pump (set)

Risk of injury!

▷

Always have repair and maintenance work performed by specially trained,
qualified personnel.

WARNING

Hot surface

Risk of injury!

▷

Allow the pump set to cool down to ambient temperature.

WARNING

Improper lifting/moving of heavy assemblies or components

Personal injury and damage to property!

▷

Use suitable transport devices, lifting equipment and lifting tackle to move
heavy assemblies or components.

Always observe the safety instructions and safety information.

(

ð

Section 7.1, Page 32)

For any work on the motor, observe the instructions of the relevant motor
manufacturer.

For dismantling and reassembly observe the exploded views and the general
assembly drawing.

NOTE

All maintenance, service and installation work can be carried out by KSB Service or
authorised workshops. Find your contact in the attached "Addresses" booklet or on
the Internet at "

www.ksb.com/contact

".

DANGER

Insufficient preparation of work on the pump (set)

Risk of injury!

▷

Properly shut down the pump set.

▷

Close the shut-off elements in suction and discharge line.

▷

Drain the pump and release the pump pressure.

(

ð

Section 7.3, Page 35)

▷

Close any auxiliary connections.

▷

Allow the pump set to cool down to ambient temperature.

NOTE

After a prolonged period of operation the individual components may be hard to
pull off the shaft. If this is the case, use a brand name penetrating agent and/or - if
possible - an appropriate puller.

«
...
34
35
36
37
38
...
»

Содержание Etaline-R





















































Отзывы:

Нет отзывов

Похожие инструкции для Etaline-R

Бренд: Eagle Страницы: 16

Бренд: VEAB Страницы: 4

Altherma EHVZ04S18DA6V

Бренд: Daikin Страницы: 16

Бренд: Daikin Страницы: 8

Altherma EAVZ16S18DA6V

Бренд: Daikin Страницы: 20

Бренд: Daikin Страницы: 56

altherma EJHA04AAV3

Бренд: Daikin Страницы: 16

Бренд: Eaton Страницы: 29

Бренд: Kamco Страницы: 36

Бренд: B+BTec Страницы: 20

Бренд: BLACKMER Страницы: 24

Shurflo 8000 Series

Бренд: Lilie Страницы: 6

CLIMAGUARD TX23

Бренд: McLean Страницы: 20

Бренд: Pentair Страницы: 16

XC Filter Cartridge EV9613-09

Бренд: Everpure Страницы: 2

Lubemate L-SSRP

Бренд: Macnaught Страницы: 4

Бренд: Barmesa Pumps Страницы: 10

Бренд: EBARA Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды