25
• Take care to put all the paper inside the
filter or you may get some drips.
Placing the E.S.E. pod correctly will create a
richer, thicker crema.
Locking the handle tightly and properly will
also help avoid leakage from the filter holder
and ensure a better brewing cycle.
Place the filter holder inside the brewing head
and firmly turn the handle as far right as
possible
(6) (7) (8)
.
As soon as the coffee selection buttons
commence to glow continuously, the machine
is ready to operate.
• Press the espresso selection button (O)
once
(9)
. Take the pre-brewing into account.
• When the recommended quantity of coffee
has been reached the appliance will stop
automatically. You can stop your machine at
any time by pressing the coffee selection
button
(9)
again.
• Remove the filter holder from the brewing
head and throw away the used coffee pod.
2. PROGRAMMING YOUR MACHINE:
Should you wish to alter the preprogrammed
quantity (50ml per cup, default setting) of
espresso filled into one or two cups, proceed
as follows:
• Fill the water container
(1) (2) (3)
and turn
on the machine
(4)
.
• Put the filter for one or two cups into the
filter holder
(5)
.
• Place some ground coffee in the filter (1 or 2
measuring scoops), and then tamp it down
firmly; the coffee should reach the lip of the
filter
(11) (12)
or a E.S.E. pod in the E.S.E.
filter
(18)
.
• Remove any ground coffee which is lying
around the filter
(13)
.
• Replace the filter holder
(6) (7)
.
• Place one or two cups beneath the filter
holder’s coffee outlets.
As soon as the coffee selection buttons
begin to glow continuously, the machine is
ready to operate.
• Press the espresso selection button (O) once
or twice according to your choice
,, or
(9) (10)
. The start / stop switch (N)
will blink. Take the pre-brewing into
account.
• Then press the scroll button (S1) to activate
the quantity memory function. The symbol
“ ” is displayed in the centre of the screen.
• When you reach the desired quantity of
coffee, stop the appliance by pressing the
espresso selection button (O) or (S2).
The quantity that just ran through into your
cup is now automatically programmed into
the machine.
3. STEAM FUNCTION
The thumping noise which occurs while steam
is being produced comes from the intermit-
tent regulation of the pump and has no effect
on the proper working of the machine.
If you wish to make an espresso
immediately after using the steam
function,
the appliance must first be allowed
to cool down in order to achieve the correct
temperature for preparing an espresso.
• As soon as you interrupt the steam cycle, the
appliance will cool down automatically by
launching an intermittent pump cycle for
40seconds. The cold water pumped through
will cool down the heating system. During
the cool down phase, the blue start/stop
operating control light blinks and the hot
water flows into the drip tray. When the
correct temperature is reached, the
appliance is ready.
Caution:
during and after use, the metal
parts of the nozzle (E) and the cappuccino
accessory (F) are very hot.
. Using the Cappuccino accessory (F)
The cappuccino accessory makes it easy to
produce hot milk or frothy milk for making a
cappuccino, latte or hot chocolate, for
example.
It is preferable to use very cold, very fresh,
milk (kept in the refrigerator).
• Fill the water container with fresh, cold
water
(1) (2) (3)
and turn on the machine
(4)
.
• Put the cappuccino accessory in place on the
steam nozzle.
• Place a cup under the cappuccino accessory.
• Pour about 100 ml of cold milk into a
container.
• When your appliance is ready to make an
espresso, press the steam/hot water button
XP2070 anglais.P65
7/11/05, 12:32
25
