Krone Comprima CF Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 34

Krone Comprima CF Скачать руководство пользователя страница 8

Operation

8

Pos: 4.29 /BA/Bedi enung /Rundballenpresse/F olienbindung/D en Foli enanfang wi e folgt in di e M aschine einl egen_text vor bild @ 470\mod_1471501328064_78.docx @ 3177267 @ @ 1

•

Insert the start of the film into the machine as follows:

Pos: 4.30 /Bei packs/R undball enpressen/F olienbi ndung/Modulgruppen F olie ei nleg en / LED Lichtl eiste/Z BBP1797 : F olienverlauf @ 468\mod_1469788643716_78.docx @ 3161484 @ @ 1

ZBBP1797_3

X

Y

1

2

3

Fig. 7

Pos: 4.31 /Bei packs/R undball enpressen/F olienbi ndung/Modulgruppen F olie ei nleg en / LED Lichtl eiste/Beschr eibung 3: Foli e einl egen @ 470\mod_1471437037800_78.docx @ 3176830 @ @ 1

•

Pay attention to the points along the path of the film that are identified with an eye.

•

Make sure that the film overhang is at least

X=250 mm

.

•

Hook the eyelet bolt (1) at the upper cone (2) into the support/holder on the clamping

lever.

The dimension

Y=30 mm

is set at the factory.

•

Check whether the locking pin with the knob (3) is locked.

If the locking pin with the knob (3) is not locked, see chapter Settings, "Adjust film brake".

If film tying is started, the net rocker arm moves down and the film overhang

X=250 mm

is

conveyed from the first two rollers to the round baler. At this point, the film sticks to the round

bale and is pulled along with it.

Pos: 4.32 /BA/Bedi enung /Rundballenpresse/F olienbindung/Hinweis auf T er minal " Auswahl Bi ndeart"_nurBA_C ompri ma @ 389\mod_1445412274043_78.docx @ 2780185 @ @ 1

Note

Before starting with film tying, film tying must be selected in the terminal, refer to chapter

Terminal - Menus, “Selection of Type of Tying”.

Pos: 4.33 /Layout M odul e /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

«
...
6
7
8
9
10
...
»

Содержание Comprima CF



































Отзывы:

Нет отзывов