manualshive.com logo in svg

Krendl GV230, Руководство пользователя, Страница: 18 / 22

Поделиться
Скачать
Krendl GV230 Скачать руководство пользователя страница 18

Rev. Date: 12/20/21

Page 15

Bearings:

Bearings are prelubricated, double-sealed, self aligning ball bearings.  They have grease fittings and should be

periodically lubricated at least once a month.  The lubrication schedule should be carefully followed.  These bearings are

filled with Mobil Mobilith SHC460 grease at the factory (18W suffix).  This grease is a lithium-thickened lubricant having

mineral base oil.  The useable working temperature is -40  F to +300  F.  

Note: It is recommended to check to make

sure the grease that is being used is compatible with the SHC460 grease as the mixing of incompatible

grease can cause lubrication breakdown.

  Proper lubrication intervals should be determined based on the observed

condition of the purged lubricants.  If the purged lubricants appear to be contaminated, then continue to purge the bearing

until the lubricant is found to be in new condition.  If bearings produce noise or heat 

(too-hot-to-touch)

, the bearings

should be replaced.

Bearing Replacement:

Remove the four bolts from bearing flange and loosen (2) set screws on bearing hub.  Since all set screws are installed

with a medium grade Loctite, a propane hand torch maybe used to assist in removing them.  Do not overheat unit, causing

shaft to expand.  A bearing puller can be used to remove the bearing.  Eliminate any metal burrs from shaft with file and

install new bearings with felt seals.  Use a medium grade Loctite on set screws before securing bearing to shaft. (Check

shaft diameter before ordering bearings)

Belt Removal for Replacement:

1. Remove belt guards.  (See Illust. K)

2. Loosen 1/2" bolt on idler to relieve belt tension.  (See Illust. L)

3. Remove (4) bolts and loosen (2) set screws on back bearing.

(See Illust. K)

4. Remove back bearing and bearing shim.

5. Remove belt from pulleys and pull belt out through opening in

frame.  (See Illust. M & N) 

Note:  Pull top of belt towards chamber

and bottom of belt out opening.

O

O

Belt Guards

Bearing & Bearing Shim

(Illust. K)

Idler Bolt

(Illust. L)

Opening

(Illust. M)

(Illust. N)

Belt

Содержание GV230























Отзывы:

Нет отзывов