Kremlin-Rexson PU 3000 Скачать руководство пользователя страница 35

Страница: 35 / 43

KREMLIN REXSON

Page 34

Manual : 573.199.112



FLUID SECTION, MODEL 50 (BASE) (REFER TO DOC. 573.080.050)

Guards (air motor cover, coupling shields, connectors,…) have been designed for

safe use of the equipment.

The manufacturer will not be held responsible for bodily injury or failure and / or

damage to property due to removal or partial removal of the guards.

SUCTION VALVE

Unscrew the suction valve (5) holding the cylinder (2).

The ball (10) is secured on the valve (5) by means of a circular rush (9).

Clean the parts.

Reinstall the suction valve (5) and the seal (25) changing the parts if necessary.

EXHAUST VALVE AND MOBILE PACKING

Unscrew the cylinder (2) and pull it downwards.

Unscrew the exhaust valve (6) holding the piston (3).

Take off the ball (17), the washer (12) and the seal (13).

Clean the parts.

Carry out the reassembly in the reverse order of the disassembly :

- Install the GT seal (13), the GT washer (12) and the ball (17) on the exhaust valve (6).

- Screw the exhaust valve (6) into the piston. Tighten up the seal on the exhaust valve (6).

Change the seal (8) if necessary when assembling the cylinder (2).

UPPER PACKING

Disassemble the piston rod from the motor and
the piston (3) from the fluid section.

Unscrew the wetting-cup (4) by means of the
wrench supplied with the pump.

Pull the piston (3) upwards to remove the seals
(21 and 22) from the upper packing (18).

Reinstall the seals (21 and 22) taking care of the

direction

, the

order

and the

dimension

assembly.

Tighten the wetting cup (4).

After reassembling the parts, fill the pump
with solvent and increase the pressure to its
maximum. Stop the pump and depressurize
opening the drain valve.

Tighten the wetting cup (4) by means of the
wrench to be in accordance with the above
drawing.

Before reassembling the different components :

- Clean the parts with the appropriate cleaning solvent,

- Install new seals if necessary after having lubricated them with PTFE grease,

- Install new parts if necessary..

Содержание PU 3000












































Результаты поиска

Содержание PU 3000

Отзывы:

Похожие инструкции для PU 3000

Бренды по названию

Популярные бренды

Kremlin-Rexson PU 3000, Инструкция по эксплуатации

Результаты поиска

Содержание PU 3000

Отзывы:

Похожие инструкции для PU 3000

Бренды по названию

Популярные бренды