Kremlin-Rexson PU 3000 Скачать руководство пользователя страница 28

Страница: 28 / 43

KREMLIN REXSON

Page 27

Manual : 573.199.112



TROUBLESHOOTING

For any intervention on the machine :

- Flush the circuits,

- Shut off the compressed air,

- Depressurize the hoses by triggering the gun,

- Shut off the electric supply.

If a problem occurs during the machine operation, alarms will be displayed on the screen of the machine.

Input

to disable each alarm.



DIAGNOSTICS

ELECTRIC

FAULTS

CHECKINGS

Check that the isolating switch is on 'I'.

Check that the mains supply is connected.

No : connect it.

Check that the fuse on the electric card inside the
box is in working order.

No : change the fuse (ind. 3).

The machine does not switch on

Check the electric wiring of the supply cable (bad
contact or other)

TROUBLES

CAUSES

SOLUTIONS

Trouble on the BASE fluid section

Check the BASE circuit :

- material in the drum,

- suction rod strainer,

- pump valves.

Clean or change.

Check the CATALYST pressure towards
the BASE pressure.

Trouble on the CATALYST fluid
section

Check the CATALYST circuit :

- material in the drum,

- suction rod strainer,

- pump valves.

Clean or change.

Check the CATALYST pressure towards
the BASE pressure.

Incorrect mixing ratio

Flow incorrectly adjusted

Check the material levels in the supply
drums.

Check the starting of the pumps.

Check the CATALYST pressure towards
the BASE pressure.

Irrelevant data capture between the
ratio

and

the

injection

volume

(Machine

unable

give

the

parameters requested)

Check that the P1 parameter (ratio) and
the P6 parameter (injection volume) are
compatible in injection capability terms
in relation to the ratio requested.









Содержание PU 3000












































Результаты поиска

Содержание PU 3000

Отзывы:

Похожие инструкции для PU 3000

Бренды по названию

Популярные бренды

Kremlin-Rexson PU 3000, Инструкция по эксплуатации

Результаты поиска

Содержание PU 3000

Отзывы:

Похожие инструкции для PU 3000

Бренды по названию

Популярные бренды