Krell Industries Evolution Two Скачать руководство пользователя страница 31

Страница: 31 / 60

The following steps describe how to connect an Evolution Two preamplifier to
your system:

Connect each power supply chassis and preamplifier chassis with the 12-pin

DC cable provided, using the DC power connectors (47) on the back panels

(1-2).

IMPORTANT

Never connect two power supplies together.

In order to operate the Evolution Two preamplifier in linked mode, connect the

preamplifier channels together with the supplied RJ-45 control cable. In linked

mode, functions including power, volume, balance, phase, record, mute, and

input selections are instantaneously transmitted between linked preamplifier

channels.

When a system with linked Evolution Two preamplifiers is powered on, left/right

orientation is established immediately, with no user intervention. For more

information on linked preamplifiers, see Appendix: CAN Link and Multiple

Evolution Two Preamplifiers, on page 51.

Neatly arrange and organize wiring to and from the Evolution Two preamplifier

and all components. Separate AC wires from audio cables to prevent hum or

other unwanted noise from being introduced into the system.

Connect the outputs of your source equipment to the appropriate CAST (34),

balanced (30), single-ended (31), or tape inputs (32, 33) on the Evolution Two.

Connect the appropriate main outputs (35-41) on the Evolution Two to your

amplifier.

On each preamplifier channel, connect the supplied AC power cord to the IEC

power cord receptacle (48).

On each preamplifier channel, plug the AC power cord into AC power. The

front panel display (15) scrolls through

EVOLUTION 2 SOFTWARE VERSION,

and the

red stand-by LEDs illuminate (4), indicating that the Evolution Two preamplifier

is in stand-by mode. The scrolling stops when the Evolution Two is ready to be

powered on.

Note

Use only the power cord provided with the preamplifier channel to make the connec-

tion to AC power. Operation with a power cord other than the one supplied by Krell

could induce noise, limit current, or otherwise impair the ability of the preamplifier chan-

nel to perform optimally.

continued

Содержание Evolution Two





























































Результаты поиска

Содержание Evolution Two

Отзывы:

Похожие инструкции для Evolution Two

Бренды по названию

Популярные бренды

Krell Industries Evolution Two, Руководство пользователя для владельца

Результаты поиска

Содержание Evolution Two

Отзывы:

Похожие инструкции для Evolution Two

Бренды по названию

Популярные бренды