background image

R

DK1100 TP/FP

19

Air System Prefi lter

An Air System Prefi lter is provided to maintain a clean, 
moisture-free supply of compressed air to the machine. The 
Air System Prefi lter reservoir should be routinely drained of 
moisture. To drain moisture from the reservoir either push the 
drain valve up toward the reservoir or to the side to use system 
air pressure to drain the collected fl uid. If the Air System 
Prefi lter reservoir needs to be removed to clean or replace the 
fi lter, make certain your machine is DISCONNECTED from the 
AIR SUPPLY. Cycle the machine via the foot switch several 
times to remove air from the system.

Air System Lubricator

An Air System Lubricator is provided to maintain proper 
lubrication to the pneumatic motor. The Air System Lubricator 
is fi lled with air motor oil and the Air System Lubricator 
comes preset at 1/2 turn open. The oil level in the Air System 
Lubricator should be routinely checked and refi lled with 
air motor oil comparable to the oil provided. Normal use of 
the machine will cause a light fi lm of oil to accumulate on 
the underside of the Top Plate where the pneumatic motor 
exhausts. Make certain your machine is DISCONNECTED 
from the AIR SUPPLY when fi lling the Air System Lubricator. 
Cycle the machine via the foot switch several times to 
remove air from the system.

Drain

Lubricator
Fill Cap

Содержание DK1100 FE

























Отзывы: