background image

1. Place the wing assembly with the fexible hinge over and on top of the flange that extends out
from the motor housing. The three holes in the hinge will line up with the three holes in the
flange.
2. Place the locking plate on top of the flexible hinge. NOTE: The three holes in the locking plate
are off center. Position the locking plate with the edge closest to the holes facing towards the
wing. (See Figure 2A).
3. Insert the bolts through the locking plate, the flexible hinge, and the flange on the motor
housing.
4. Place the nuts on the bolts under the wing. Hold the wings in the up position while tightening,
this will insure proper alignment. (DO NOT OVERTIGHTEN!)
5. Test the wings. Hold the wings in the up position. When
released, the wings should fall down and lie flat.

Step 2. Attach The Seal

The flower vacuum seal is reversible and has no designated
up or down surface. Wet the seal before stretching over the
foot pad. The vacuum seal should be gently stretched over the
footpad at the base of the motor housing (see Figure 3) so that
it will rest on top of the footpad. Once in place, the seal
should rotate and turn freely about the base of the motor
housing. See Figure 4.

Step 3. Attach The Roller Bumper Strap

Insert the bottom end of the strap into the slot provided on
the main body. Insert the top end of the strap into the
locking clip attached to the swivel head. See Figure 5.

Step 4. Attach The Dive Float Restrictor

Snap the float restrictor into place between the dive floats. Be sure to attach the restrictor only in
the area between the floats ranging from the base of the floats to upwards 2” as shown in the
illustration. See Figure 6.

Figure 5

Locking

End Clip

Flat Tab

Figure 6

5

Figure 3

Figure 4

Vacuum Seal

Footpad

Содержание Pool-cleaning system















Отзывы: