background image

Kramer Electronics Ltd. 

 

VM-3H2 

– Connecting the VM-3H2 

 

Connecting the VM-3H2 

 

Always switch off the power to each device before connecting it to your 

VM-3H2

. After 

connecting your 

VM-3H2

, connect its power and then switch on the power to each device. 

 

 

You do not have to connect all the inputs and outputs, connect only those that are required. 

 

To connect the 

VM-3H2

, as illustrated in the example in 

Figure 2

, do the following: 

1.  Connect an HDMI input source (for example, a 4K Blu-ray player) to the HDMI IN 

connector. 

2.  Connect the three OUTPUT connectors to up to three HDMI acceptors, as follows: 

 

Not all outputs need to be connected. 

 

 

HDMI OUT 1 connector to HDMI acceptor 1 (for example, a 4K display with 
speakers). 

 

HDMI OUT 2 connector to HDMI acceptor 2 (for example, a 4K display with 
speakers). 

 

HDMI OUT 3 connector to HDMI acceptor 3 (for example, 4K plasma display). 

3.  Connect the 5V DC power adapter to the power socket unit and then connect the 

adapter to the mains electricity 

(not shown in 

Figure 2

).  

See 

LED Indications

 on page 

5

 for the state of the LED indicators during and after 

powering on. 

 

Figure 2: Connecting the VM-3H2 1:3 4K HDR HDMI DA 

  

  

  

Содержание VM-3H2

















Отзывы: