background image

Overview 

 

Overview 

The 

TP-310A

 

UXGA Line Receiver/DA

 receives a CAT 5 signal from a 

transmitter

1

The 

TP-310A

 serves as a power center that can distribute power to both the 

transmitter and the connected receivers (see section 

 and distributes it to up to 10 other receivers (via CAT 5 cables). 

The 

TP-310A

 also decodes the CAT 5 signal and simultaneously distributes 

it to two UXGA outputs, two analog audio outputs, two digital audio 

outputs and two RS-232 outputs. 

 3.1

). 

In particular, the 

TP-310A

 

Has a resolution of up to UXGA 

 

Has two UXGA outputs on 15-pin HD computer graphics video 

connectors 

 

Includes two digital audio outputs (S/PDIF) on RCA connectors and 

two analog audio outputs on 3.5mm mini jacks 

 

Has a transmission range of up to 300ft (up to 100 meters) over STP 

cabling  

 

Can change the polarity of decoding H and V Sync for video (UXGA) 

 

Includes EQ. and LEVEL controls for the video (UXGA) output 

The 

TP-310A

 

is housed in a 19” 1U rack mountable enclosure, with rack 

“ears” included, and is fed from a 100-240V AC universal switching power 

supply. 

3.1  About the Power Connect Feature 

The Power Connect feature applies as long as the cable can carry power. 

This feature is available when using STP cable and the distance does not 

exceed 50m on standard CAT 5 cable. For longer distances, heavy gauge 

cable should be used

2

For a CAT 5 cable exceeding a distance of 50m, separate power supplies 

should be connected to the transmitter and to the receiver simultaneously.

 

.

 

For units which are connected via RJ-45 connectors, 

make sure that the shield of the STP cable is connected to the metal casing 

of the connectors on both ends of the cable. For units which are connected 

via terminal block connectors, the shield of the STP cable must be 

connected to a ground terminal on the units at both ends (use the ground 

terminal of the power supply connection if necessary). 

                                                       

 

1 For example, the Kramer TP-121, TP-123 or TP-45 
2 CAT 5 cable is still suitable for the video/audio transmission, but not for feeding the power at these distances 

Содержание TP-310A



















Отзывы: