Kraga Roa II Скачать руководство пользователя страница 14

spars in place. 

Pre-drill also screw holes on servo plate. It is easier to attach servos to the servo plate before 
inserting servo plate into the fuselage and screwing servo plate to the servo holder plate. 

Make sure, that wing joiner carbon tubes (8x6_515 and 8x6_485) fit into main wing spars, if not, 
use drill and wet sanding paper as described in the beginning of this guide to make them thinner. 
You can glue the wing joiners into the fuselage pod permanently or keep them removable for easier 
transport.

Tail

To complete tail assembly first shorten all hinges and then insert the hinges into hinge slots and 
apply the glue from inner side of the main tail. Then insert all hinges into hinge slots on moving 
part of the tail and put the glue from inner side of the moving part. Tip of the moving part should be
aligned flush with main part. Be very careful when using glue near pinned part of the hinge.

Before gluing tail surfaces to the tail_mount, dry fit protruding spars of the tail surfaces into 
tail_mount. Apply the glue on the protruding spars and insert them into tail_mount.

Insert boom into tail_mount. Aline the tail correctly with rest of the fuselage (use joiner rods as 
helping guide). Then you can apply the glue from the front side of tail_boom_mount. It has tiny 
channels for glue to soak in along the boom.

[email protected]

Содержание Roa II


















Отзывы: