background image

WARNING: If the information in these instructions

is not followed exactly, a fire or explosion may

result, causing property damage, personal injury

or loss of life.

MODELS:  

#PRC-36 / #PRC-36-RF

‘PRINCETON’

Direct Vent Gas Fireplace 

INSTALLATION AND

OPERATING MANUAL

US Patent #6004493

Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance.

WHAT TO DO IF YOU SMELL GAS

:

Do not try to light any appliance.

Do not touch electrical switches; do not use the

phone in your building.

Immediately call your gas supplier from a

neighbor’s phone.  Follow your gas supplier’s

instructions.

If you cannot reach your gas supplier, call the fire

department.

Installation & service must be performed by a qualified

installer, service agency, or the gas supplier. 

This appliance is only for use with the type(s) of gas

indicated on the rating plate and may be installed in an

aftermarket permanently located, manufactured (mobile)

home, where not prohibited by local codes.   See owner’s

manual for details.  This appliance is supplied with a

conversion kit.

       

IMPORTANT:

READ INSTRUCTIONS CAREFULLY BEFORE INSTALLATION.  FAILURE TO

INSTALL THIS FIREPLACE CORRECTLY CAN CAUSE SERIOUS STRUCTURAL

AND FIRE HAZARDS AND MAY VOID YOUR WARRANTY

.

                                                                         

www.kozyheat.com

    

                

Report No. 216-F-10-5

March 2006 (2)

Содержание PRC-36







































Отзывы: