Korg Trinity plus Скачать руководство пользователя страница 168

Страница: 168 / 194

Various messages

160

Various messages

Audio tracks were skipped

Battery Low

Can’t Calibrate

Completed

Destination and source are identical

Destination is empty

Destination measure is empty

Destination song is empty

Destination start measure within the limits of source

Directory not empty

Error in formatting medium

Situation:

On a

TRINITY series

instrument which does not have the

HDR-TRI

option, you

attempted to load a file that included an audio track, and the data was loaded without
the audio track.

Situation:

The internal battery has run down.

Action:

Be sure to contact your dealer or a Korg service center.

Situation:

Calibration could not be performed correctly.

Action:

Try the command once again.

Situation:

This will appear after a command has been successfully executed.

Situation:

When copying or bouncing, the same song, track, or pattern was selected for both
source and destination.

Action:

Select a different song, track, or pattern for the source and destination.

Situation:

When editing, the track or pattern specified as the destination contains no musical
data.

Action:

Specify a track or pattern that contains musical data.

Situation:

When editing, the measure specified as the destination contains no data.

Action:

Specify a measure that contains data as the destination.

Situation:

The song specified as the copy or bounce destination does not exist.

Action:

Before copying or bouncing, execute Create New Song in the dialog box that appears
when you select a new song.

Situation:

When using the Move Measure operation for All Tracks or within the same track, the
specified destination measure is within the source measures.

Action:

Specify a destination measure that does not fall within the source.

Situation:

When you attempt to erase a directory, one or more files or another directory may exist
within the directory.

Action:

Erase all files or directories within the directory.

Situation:

When attempting to format a floppy disk on the Trinity, a faulty sector was found on
the disk, so formatting was not possible.

Action:

Use a different floppy disk.

Содержание Trinity plus



































































































































































































Результаты поиска

Содержание Trinity plus

Отзывы:

Бренды по названию

Популярные бренды

Korg Trinity plus, Руководство по параметрам

Результаты поиска

Содержание Trinity plus

Отзывы:

Бренды по названию

Популярные бренды