Korea Nakajo NID-1520T3, Инструкция по эксплуатации

Страница: 17 / 24

* Never disassemble, repair, and remodel the product without instruction.
* Contact the service center if there is an abnormality of the product.
Is ice sticking together?
Symptom Identification Action-taking
Power lamp is off. 3 selection buttons
Open the front panel and check the digits
Refer to the table below for Information function.
are blinking at the same time. of the setting monitor.
※
If it continues, contact the service center.
The product fails to make ice.
①
Is ice being produced now?
①
Wait for a while to start outputting.
②
Is ice clogged in the output?
②
Remove the ice in the output.
③
Is ice remained in the stocker due to the no use
③
Turn off the power and wait until the ice melted
of the product for a long time?
Water flows at the bottom of the product.
①
Is drip tray out of place?
①
Set the drip tray in the proper place.
②
Is there a clogging in drain hose?
②
Remove clogged part in the hose.
The product fails to make ice.
①
Is the valve of water supply pipe closed?
①
Open the valve of water supply pipe.
②
Is water supply cut off?
②
Use the product after water supply started.
③
Is separately installed water purifying filter clogged?
③
Change the water purifying filter.
completely.
②
Is the switch ON?
Error indication Errors Measures
Can not turn the power on.
①
Is the power plug disconnected from an
①
Insert the power plug to an electrical outlet.
electrical outlet?
②
Turn the power switch lever ON.
E1 Failure of water supply
①
Check the connection of water supply pipe, water stop valve,
and suspension of water supply.
3-3. Before requesting repair: Trouble shooting
Check the following items before requesting repair.
Information function for safe use
(ambient: temperature within 10-35
℃
)
supply. (within0.1-0.3MPa)
③
Check if the inner part of strainer is clogged, and change the filter.
④
Contact the service center if it happens repeatedly.
＊
After processing, the situation will be reset when starting the product.
E2 Failure of water drainage
①
Re-start the power switch.
②
Contact the service center if it happens repeatedly.
E1 Failure of water supply
①
Check the connection of water supply pipe, water stop valve,
and suspension of water supply.
②
Check if water pressure of water supply pipe is low, and lack of water
E3
Temperature of Inner part of the product below
5
℃
When the room temperature is above 5
℃
, the product will recover
automatically.
Improve the surrounding environment of the product.
(ambient: temperature within 10-35
℃
)
E4
Temperature of inner part of the product over
50
℃
When the room temperature is below 50
℃
, the product will recover
automatically.
Improve the surrounding environment of the product.
the power switch to restart.
E6 Over Cooling Condenser (Evaporator)
①
Turn OFF the power switch, and wait for 30 minutes. Then turn ON
the power switch to restart.
②
Contact the service center if it happens repeatedly.
E5
Over heating Condenser (Condenser)
①
Be sure to place the product away from the heating-source.
②
Check the inlet/outlet is not covered by the product or others.
③
Turn OFF the power switch, and wait for 30 minutes. Then turn ON
E9 Information function Contact the service center or the seller for the periodical inspection.
E7
Abnormality of Geared Motor
①
Turn OFF the power switch, and wait for 30 minutes. Then turn ON
the power switch to restart.
(Ice-making motor)
②
Contact the service center if it happens repeatedly.
E8 Failure of ice-making function
①
Turn OFF the power switch, and wait for 30 minutes. Then turn ON
the power switch to restart.
②
Contact the service center if it happens repeatedly.
E9 Information function Contact the service center or the seller for the periodical inspection.
E8 Failure of ice-making function
②
Contact the service center if it happens repeatedly.
EF Abnormality of FAN MOTOR Contact the service center.
■
It is a full-ice detection error, when all the setting of the monitors are correct but, unable to make ice with no sign of error.
17