background image

14

VIII. Maintenance

 

 

Kooltronic Air-Cooled Air Conditioners require no maintainance. In the event of a problem with your air 
conditioner, please follow the instructions below. 
 

A. Blowers

 

 

The design life of the blowers used in all Kooltronic Air Conditioners is substantially in excess of 
20,000 hours. All Kooltronic condenser and evaporator blowers are equipped with automatic-reset 
thermal overload protectors. 

 

CAUTION

 

 
 
 

If field replacement of a blower motor is necessary, most blower assemblies, including the mounting 
plate, are readily removable. Each of the blower mounting plates is held to the air conditioner cabinet 
structure by screws and nuts. For installation of the replacement blower, electrical connections may 
be broken at the terminal block, or power leads may be cut and appropriately spliced together.  

 

B. Compressor

 

 

All Kooltronic compressors are approved by UL and CSA, and require no maintenance. They are 
hermetically sealed and charged at the factory, and equipped with automatic-reset thermal overload 
protectors. 
 
If the compressor fails, it is strongly recommended that the air conditioner be returned to Kooltronic 
for service. 

 

C. Refrigerant Loss

 

 

Kooltronic Air Conditioners are subjected to a series of tests to detect refrigerant leaks, during and 
after manufacture. It is possible that shipping or other damage, or microscopic leaks over a long 
period, may result in the need for replenishment of refrigerant charge.

 When it has been verified by 

a Certified EPA Technician that a refrigerant shortage does exist, the leak must be repaired. 
Then the unit may be evacuated and recharged in the field by a Certified EPA Technician only. 

 

CAUTION 

 

 
 

 

D.  Relocation

 

 

If your Kooltronic Air Conditioner has to be moved to another location by truck, the following 
precautions should be taken: 

De-mount the air conditioner from the equipment, controller or enclosure. 

Conform to the applicable provisions of PROCEDURE FOR PROPER PACKING AND 
SHIPMENT OF KOOLTRONIC AIR CONDITIONERS in this manual under 

Section III. 

Before opening the air conditioner, disconnect all power.

Refer to the data on the unit name plate which specifies the type of 

refrigerant and the amount of charge in ounces. 

Содержание Intrepid Series


















Отзывы: