SAFETY NOTES
- Please consider the information provided in the setup instructions
- Also consider the safety and assembly instructions of the keyboard
-
stand
- First perform a visual inspection, to determine if the universal holder
-
is complete and to the extent possible in working order.
- Damaged parts may not be used again.
- We recommend that the stand tube is always mounted vertically.
-
This position is the safest and has the least strain.
-
The back gears of the locking bracket provide
-
for easy corrections e.g. after adjusting the X-keyboard stand.
- Ensure that the screws are tight for all of the involved products
COMPONENTS - OVERVIEW (A-k)
A
Stand tube ø 25 x 450 mm with
a.1
Threaded bolt 3/8".
Accessory bag:
b
Thread adapter 5/8",
c
Aluminum knurled washer 3/8",
d
Clamping knob M8 x 50 mm,
e
Locking disk,
f
Spring,
g
Snap-in bracket,
h
Locking nut M8,
j
Socket head screw M8 x 20 mm,
k
Allen wrench / hexagon key SW6.
MOUNTING OF COMPONENTS (1-5)
1
Place Clamping knob
d
through one of the 8 existing
1
drill holes on the stand tube - under consideration of the
1
desired placement
2
The threaded bolt (25 mm) projects out of the tube.
2
The lock disk
e
and the spring
f
are placed on the threaded bolt
3
Then the clamping knob is placed into the internal thread of
3
- of the snap-in bracket
g
- as far as it will go
3.a
NOTE: the back gear of the locking disk
3.a
and Snap-in bracket must be aligned properly,
3.a
as to avoid the grinding of the teeth
4
The locking nut
h
is placed in one of the hexagon
4
recesses of the Snap-in bracket
5
The Socket head screw
j
is placed from the other side
5
and is screwed into the Locking nut - be sure not be screw
5
it in too tightly
MOUNTING to the KEYBOARD STAND (6-11)
Prerequisite for the stand with support tube ø 30 x 350 mm: please
refer to K&M X-Keyboard Stands 18930, 18933, 18940, 18990 and
18995.
A. Prepare the keyboard stand:
6
Setup the keyboard stand so that it is ready for use (Height, Width)
7
Place the rubber into the support tube at least 40 mm deep
8
Remove the cap
B. Attach the universal holder
1
9
Place the snap-in bracket over the support tube as far as it will go
10
Place the stand tube in a vertical position
11
Secure the snap-in bracket to the support tube and tighten
11
the recessed socket head screw M8 x 20 mm
SETUP INSTRUCTIONS
18944 Universal holder
- Universal holder for all X-Keyboard stands with 30 mm support tube arm
- Recommended for K&M Models with 350 mm depth:
-
18930, 18990 (Lever operation) as well as 18940, 18995 (locking knob).
- Enable the expansion of the keyboard stand with: Music desk
-
swivel arm, swan neck, iPad Holder, Tablet PC Holder etc.
- 3/8"-connection thread including 5/8" adapter
- 8 height adjustments in 42 mm intervals
Thank you for choosing this product. The instructions provide directions
to all of the important set up and handling steps. We recommend you
keep these instructions for future reference.
KÖNIG & MEYER
GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
18944-000-55 Rev.04 03-80-326-00 5/18
COMPONENTS - OVERVIEW
MOUNTING OF COMPONENTS
MOUNTING to the KEYBOARD STAND
A. Prepare the keyboard stand
B. Attach the universal holder
