Konica Minolta SRX-101A Скачать руководство пользователя страница 25

Страница: 25 / 31

OPERATION MANUAL 23

SERVICE AND MAINTENANCE

1. Put the DEV rack first, and then FIX/WASH

rack.

2. When re-installing each rack, make sure to

set the rack rib properly into its groove.

• Re-install the DEV rack slowly and carefully.

• Re-install the FIX/WASH rack slowly and carefully.

1. Be careful not to splash the solution over the

film entrance sensor when you clean the
processing tank. Should the solution contact
with the film entrance sensor, thoroughly
wipe it out.

2. Use a splash guard(optional equipment) to

prevent the splash of the solution.(See page
27 as to instruction for use)

(3)Cleaning the Area Around the Processing Tanks

Scrub the area clean with a wet sponge (or clean

cloth) dipped in warm water(under 104

)

(4)Cleaning Inside the Processing Tanks

Pour a small amount of water into each tank and

scrub it clean with a sponge (or clean cloth).
Add more water for rinsing.

Open the drainage valve and empty each tank

thoroughly.

(5)Supply of the Chemical Solution

Remove the top cover.

Open the DEV and FIX drainage valves to empty

the tanks.

After the tanks are empty, close the valves.

™

DEV Rack

™

Groove

™

Rack Rib

™

FIX/WASH Rack

™

Rack Rib

™

Groove

™

Fixer Drainage Valve

™

Developer Drainage Valve

HINTS FOR RACK RE-INSTALLATION:

HINT:

Содержание SRX-101A
































Результаты поиска

Содержание SRX-101A

Отзывы:

Похожие инструкции для SRX-101A

Бренды по названию

Популярные бренды

Konica Minolta SRX-101A, Руководство по эксплуатации

Результаты поиска

Содержание SRX-101A

Отзывы:

Похожие инструкции для SRX-101A

Бренды по названию

Популярные бренды