manualshive.com logo in svg

Konica Minolta SRX-101A, Руководство по эксплуатации, Страница: 19 / 31

Поделиться
Скачать
Konica Minolta SRX-101A Скачать руководство пользователя страница 19

OPERATION MANUAL   17

OPERATING  PROCEDURES

Different ON-OFF patterns shown by the RUN and READY lamps on the control panel indicate different operating
conditions.  The following is a listing of all the possibilities and the conditions they indicate.

RUN and READY Lamps ON-OFF Patterns

9

OFF

OFF

ON

ON

ON

OFF

OFF

Flashing(Pattern 1)

OFF

Flashing(Pattern 2)

ON

Flashing(Pattern 1)

OFF

Flashing(Pattern 1)

ON

RUN

READY

RUN

READY

RUN

READY

RUN

READY

RUN

READY

RUN

READY

RUN

READY

RUN

READY

Flashing(Pattern 2)

ON-OFF Pattern

Operating Condition

Note

(1)

All operations shut down

Normal operation

(Operating temperature LOW)

Normal operation

(Operating temperature OK)

Preparing for supplying chemical
solutions
(Repl. switch ON for 5 sec.)

Supplying chemical solutions

Manual replenishment

Drive motor error

Temperature error

Pattern 1

0.5

0.5

Pattern 2

0.7

0.1

0.1

0.1

Pattern 2

0.7

0.1

0.1

0.1

Pattern 1

0.5

0.5

Pattern 1

0.5

0.5

: ON time(in seconds)
: OFF time(in seconds)

(1)

Содержание SRX-101A
































Отзывы:

Нет отзывов